after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
HI,
I have a function testfun from a customer-provided .a library, and I hope to run this testfun function in RAM. I am currently using NCS 2.8 based on the nRF52840. I...
Hi, I read others cases obout the problem to send more than 20 bytes trhough BLE and add on my prj.conf the next three lines:
This is the entire prj.conf:
Butr when...
NCS 2.7.0
NRF52840 DK
I am trying to trigger an advertising sent callback to indicate advertising timeout or a maximum number of events. I have tried increasing the workqueue...
Im using nrf5340 with nrf connect SDK 2.6.
Im trying to follow this post to evaluate hardware timer for reading saadc
But I constantly am getting
CONFIG_NRFX_TIMER1...
Hi,
I have successfully built and ran the MQTT sample ( /opt/nordic/ncs/v2.7.0/nrf/samples/net/mqtt) on the nRF9160-DK. I did have a few problems with SIM coverage and firmware...
Hi,
running the latest nrfconnect vscode extension (v2024.9.31) the "Add configuration wizard" comes up and stay blank. Additionally, the Actions view is also empty, while...
Hello
I am trying to initialize qspi in a ".cpp" file and methods like
PINCTRL_DT_DEFINE ( QSPI_NODE ); are giving me "out-of-order initializers are nonstandard in C...
Hello,
Currently, I am working on the nRF 52840 DK and the UART port named uart0 is connected to the on board debugger, Where do i find the pins for the UART1 ? I could...
Hi,
I was at the stage to do current measurment on my nrf52DK for my application, but once I cutted SB9 and powered it back by USB, the 4 leds on the board lighted up...
We are planning to base a GATT and LE Audio design off of the latest nRF Connect SDK v2.6.1 and looking into Bluetooth certification. I have found the QDIDs for the Host and...
Hello,
I am trying to use SPI driver to read BMI270 IMU data on my nRF52840dk. I stucked at verifying the sensor ID step. According to the datasheet, sensor ID is stored...
Hello,
I tried to read and write the OTP region in UICR of nRF5340 with nrfutil, but got the following output:
Any Ideas, what could be the issue here? Does nrfutil...
Hello, After consulting the manual and understanding the composition of the calibration data page, the ant_bpwr_calib_handler was added, but the callback function was not...
Hello, I want ro test the channel sounding feature using the new nRF54L15-DK /PDK and I found a sample example for reflector role - "https://docs.nordicsemi.com/bundle/ncs...
I'm migrating an nRF52840 project from ncs 2.7.0 to ncs 2.8.0. We pass the board in to the west build command line. Our CMakeLists.txt uses the BOARD & BOARD_QUALIFIERS to...
