Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
I need to develop the code for RTC configuration without using nrf_drv_rtc_* , hence I started using zephyr device tree approach . Below is my code .
#include <stdio.h...
Hello,
I recently purchased a Nordic Thingy 91 device, and I have been working on it for a few weeks. I am currently experiencing two major issues with the kit that are...
Hi,
I have a board which is nrf9151 with nrf52840 as BLE controller connected via hci_lpuart. This works fine so far, I am able to do simple AT commands as well as doing...
when I try to add a build config, i can only see a blank page for build configs.
but if i click on another project's build config which is already created, i can see the...
Hi,
I'm troubling using the retention module of Zephyr with NCS 2.6.1 on an NRF52840. I've read the Retention System Documentation of Zephyr but it is not working for me...
Folks,
Am running VSC 1.95.1 on Mageia Linux.
I have a 52833 board that I have working in that I can write to and read from custom BLE characteristics and send data out...
Hi
I'm setting up an OpenThread network and am trying to use the nRF Thread Topology Monitor to visualize the network for debugging purposes. However, no OT devices appear...
According the AT command documentation, reading the device certificate is not supported.
That's somehow irritating. There is no reason for that, at least for those who common...
Hello,
My board contains nRF9160 and nRF52840. The nRF52840 is a HCI controller (based on HCI lpuart example). nRF9160 communicates with nRF52840 over UART. I want to perform...
Hi, in our project we use nRF5340 to control some externanal peripherals as flash mem through SPI and also we need BLE comunication.
The case is if whe allow the config...
Hi, I am trying to use the DECT NR+ sample from the 2.7.0 nrfconnect sdk but I can't seem to get the following to work in the prj.conf:
the results of my build give...
Is there a way to convert the firmware for the nRF Connect RSSI viewer to work on the nRF21540DK. I imagine it isn't too difficult, since it is essentially the nrf53840 but...
I have customed a board based on nrf54l15.
Then I built the matter light_buld demo with target 'nrf54l15pdk_nrf54l15_cpuapp' and burned the file "merged.hex" into my custom...
Hello,
I'm using "Bluetooth Mesh Light switch" code which i have modified to act as a gateway. Where it periodically collects data from lights. After receiving data from...
