Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Currently, my environment uses a mobile network shared through a wired connection to an RT-AX57 router. I am working in the VSCode environment using SDK v2.6.1. Devices: Nest...
I am trying to connect a nrf5340dk to a Jetson. For now I am testing with an Arduino. I am trying to run the CanCounter example with a device tree overlay file. Also I would...
Hi,
I tried to implement the CAF LEDs module as described here . But when added the Kconfig variable CONFIG_LED_PWM =y I got the error message "CONFIG_LED_PWM was assigned...
Hi,
I was developing on Visual Studio Code earlier, and for some reason, I cannot build pristine. If I try to edit the build configuration, it never loads, and if I try...
Hi,
we are trying to make the NORA-B126 (specifically its onboard LNA) work with nrf sdk 2.3.0 by modifying the 5340dk dts and defconfig files as specified in the NORA-B1_SIM_UBX...
Hi there,
I'm working on NCS2.7.0 and nrf52840.
I used the chip-cert to generate custom DAC, PAI, and PAA with VID = 0x1234 and PID = 0x5678, then placed the...
Hi there,
Thanks for helping. We are using the nRF52840 DK along with the Power Profiler Kit 2 (PPK2) for power measurement. We are encountering periodic power spikes during...
Hi, we are designing a factory acceptance test (FAT) jig for a custom board containing an NRF9160 SiP. We are testing more than one thousand boards, and probably more than...
Hello
We are using a slave processor with AT command to communicate with the nRF9161 . This is working without problem
But we are initially using the Quick Start 0.2.7...
Hello,
I'm using nRF9160 as a HCI host and nRF52840 as HCI controller (nRF52840 config is based on HCI lpuart example). My application receives data over Bluetooth using...
We have two cases where the modem has downgraded itself from version1.3.2 to 1.3.1.
1. In the first case, due to water ingress, it appears that the reset pin has been toggled...
System: Windows 10, Vscode + Nrfconnect
I saw a previous post on same topic which fixes the issue by changing the settings in extension like said here ( changing extension...
We have pre-production product (based similar to the NRF9160dk setup with a NRF9160 (LTE-M, GPS) and a bridged NRF52840 (BLE). We are working through certifications for CSA...
Hi all,
I am aware of the different access port protection mechanisms (listed in my previous ticket here: Link ). I did also test both revisions successfully:
For...
Hi.
In our private network we experience one problem.
We can ping Google (8.8.8.8) via APN customer4. In Wireshark traces it is seen that ping is initiated.
On RRC level...
