Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello:
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
I change name by app, after get new name from my app,save it to flash, then I call gap_params_init, in this function, I reload the new name from flash and set it by sd_ble_gap_device_name_set...
Hello Nordic Community,
I’m encountering an intermittent issue with my BLE peripherals, which are based on nRF5340 + nRF7002 SoC , while testing with nRF Connect Mobile...
Hi,
We are in process of performing CE Certification on a product with the nRF9160 module mounted.
The lab wants to perform conducted testing on the module with the antenna...
hey there, i have a project which uses nrf9151 with a pressures sensor from BOSCH which uses SENT protocol to transfer data, my question is 1. Is it possible to configure...
Hello, I'm using the nrf52DK for the chip nrf52832 with nrf connect SDK v2.6.1
I want to implement an advertising timeout say 5 minutes. How can I achieve that? any example...
I'm attempting to troubleshoot a system crash when polling a sensor at higher ODRs while BLE is enabled. I'm using NCS v2.9.0 with the nRF54L15. I checked the thread stack...
I'm trying to compile the lsm6dso example for a nrf5340. I also tried the nrf52832, but I get the same error.
v2.4.2\zephyr\samples\sensor\lsm6dso
prj.conf:
CONFIG_STDOUT_CONSOLE...
Hello, i'm considering an application using nRF52840 in following configuration:
- I2S RX would be connected to some external I2S source (I2S slave)
- I2S TX would be...
Hello, I'm trying to make a application bootable through MCUBoot but I'm having a hard time generating the .bin file with MCUBoot header. According to this page I should be...
Hi I want to use nrfutil nrf5sdk-tools in MacOS but when I try to run it I get the following error.
" Error: Failed to spawn inner nrfutil-legacy executable
Caused by...
We are trying to update the SDK used by a firmware on a device that is in production. The old SDK is 2.1.0 and we are trying to update to 2.9.0.
I was able to get the firmware...
i am currently using nrf52840 dk as a hardware, nrf5sdk version 17.1.0 ,ble_app_uart peripheral example (s140 soft device )
here the maxmimum mtu is set to 247 bytes whether...
Hi everyone, When I try configure UART (parity, data_bit, stop_bit, flow_ctrl), I have noticed error when I run in terminal: "
*** Booting nRF Connect SDK v2.9.0-7787b2649840...
Hello
I am developing an application based on the nRF9160, it uses Coap protocol to connect to nRFCloud to transfer the data. Also I have implemented the FOTA which always...
Hello,
I am using the nRF52810 with SoftDevice S112_nrf52_7.0.1 and trying to create a simple program that sends the character "1" to a mobile device. However, I am encountering...