Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I have simple Bluetooth commination working. I can connect to nRF52840 with your nRF Toolbox on my Android. I can send a string from the nRF52840 to the Android app and have...
Hi,
I found this code for adafruit BNO055 sensor on GitHub which is a Arduino code.
https://github.com/adafruit/Adafruit_BNO055
How can I import this on the Nordic nRF5340...
Hi all, I'm searching for a SPI example with NCS 1.8, I'm currently using nrf52840dk_nrf52840. I've looking at the drivers (nrfx_spi) but I still don't get it at all, so I...
Hi, I have a Nordic Thingy 91. I need it to save battery and transmit sensor data to Nordic Cloud on PIR external interrupt (if I could count number of PIR pulses that would...
Hi I am testing the Thread examples
I worked on SIMPLE_COAP_EXAMPLE in nrf52840 DK there it works fine while opening UART and enter to CLI commands and its working
but...
Hi again Nordic. I'm trying to write sensor data to the external flash continuously as there is not enough RAM to hold all the data required. However, the writing operation...
Hi,
I am using BL653 dvk to write an application for SPI, In my prj.conf, I added below parameters:
Now when I am debugging SPI master code, execution enters the file...
We are performing a preliminary power analysis with this device and have questions regarding the power consumption reported in the Product Specification. For example, the...
I've been struggling with enabling HTTP support on the serial_lte_modem. I've tried using various versions, currently I'm using NCS 1.8.99. I edit the prj.cnf to include CONFIG_SLM_HTTPC...
Hi,
I use nRF52840 and SoftDevice s140 (7.2.0). I use SEGGER Embedded Studio to compile a project written in C++. But lately I've been having trouble debugging. For example...
i've been test code from nrf51-app-button-example/main.c at master · NordicPlayground/nrf51-app-button-example (github.com) but not effect when presss any button.
I am new to Zephyr and Nordic. I onserved that to use variuos APIs it is required to declare in prj.conf file. But, where is the list and document of various commands woth...
Hi
I have a Nordic nRF51 as a Peripheral.
I have it open advertising until it connects for the first time to an Android handset.
When a connection is made it stays...
When I switch to any branch other than 1.8.0-rc2, I get the following notification:
"This workspace requires version 1.8.0-rc2 of the nRF Connect SDK, but it isn't installed...
