Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Peripheral: nRF52840 DK Central: OnePlus 6T, nRF Connect app
I modified ble_app_uart example, to support Bluetooth Long Range:
I observe two issues:
Advertising...
We were thinking to use nrf52840 dongle for one of our key projects. We were able to integrate the dongle in our ecosystem with android app.
But we have users of the product...
I have a problem about BPROT function, the project is on nrf52832 and using SDK 15.3, Softdevice s132 6.1.1.
If I enable the BPROT function by calling nrf_bootloader_flash_protect...
Nrf52832, SDK 13.0 Softdevice 132 PMIC: bq25150
I have a battery powered BLE device. When a user takes off the battery and put it back and powering on, the device does...
i set the connected time is 30ms
but i use dongle to grab the bag ,i find that the connection parameters were wrong , it can not fix at a value
it looks like it change...
Hello,
This issue is related to this ticket , before continuing I recommend to read it first.
I had suspicion that the "speed" improvement is between project compiled...
Hello,
I recently opened a ticket, with several questions about the mesh network, I had some evolutions and new questions emerged.
We have a firmware already consolidated...
Hell there Can I find an SDK that is supported on Nrf52805 chip? Or can I get any proper guidance on program of nrf52805 (the module MS46SFIi) together with Segger Studio...
I combined the BLE UART and SPIS Peripheral example of SDK V17.0.2 to receive data from a microcontroller using SPIS protocol in every 32 milliseconds and send it over through...
Hi Sir,
nRF Connect: v3.6.1 NCS: v1.5.0 and use original example to build code, Net core: hci_rpmsg example Application core: peripheral_uart example
H/W device: nRF5340...
Dear NCS experts, The development system is running:
Ubuntu 21.10
nRF Connect SDK (btw., where's can the installed version be seen?)
VS code (1.62.1 - in portable...
Good evening,
From testing my Nano 33 BLE , I've discovered that the following settings are reversed with respect to "High" and "Low", i.e., LEDs light up for Low, and turn...
I need to interface my sensors by using twi. Here one of my sensor is smbus compatible. For I2C, I need to read acknowledge from sensor. So i need reference or samples to...
I have update my thingy91 with thingy91_ltem_dfu_2020-04-29_bc7ade8b.hex and mfwnrf9160120 as I was not longer able see anything in nrfcloud.The
Thingy91 does not connect...
Hi team,
i first of all want to thank you, for your support and help so far.
I have some questions regarding the values that are been given by the AT command %CONEVAL...
