Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
I am using flash_fstorage_s140_pca10056 example from SDK v17.0.2 , I see that the start address is 0x0003 E000 and the end address is 0x0003 EFFF respectively.
I want to...
Hi,
I am trying to check how DFU works but I have problems setting it up. I will describe all the steps that I have been doing here, so that it will be easier to try to...
Hi, I am designing a custom board usign the NRF52832. Im using this externar crystal https://es.rs-online.com/web/p/unidades-de-cristal/1753468/ . but I have seen that many...
Hello Nordic Support Team
I need desperate help to get my proof of concept working. I have been able to prove that the applicational concepts work on the nRF52840 and now...
I'm trying to create an application on the nRF52840 that can read serial input from an external GPS chip and also provide log output via USB. As I understand it, the UART...
I want to read access address of a connection between master and slave in master.
I need access address and not the MAC address after connection establishment.
Is there...
Hello, when developing our application, we run into a problem. We are running Zephyr 2.4.0 on nRF52840 MCU. We use LSM303AGR sensor, which is supported by zephyr LIS2DH driver...
Hi,All:
1. As the topic, now i just make bootloader,How do i perform a app entrance? and how to staging, combing.........in the picture as below. Or,on the other hand,how...
Dear,
I am trying to manually toggle GPIO0_2 by writing into the GPIO register, 0x50842504[bit 2]. The output of GPIO0_2 was always static in either high or low.
If...
We use the Nordic library for mesh with Gatt proxy service to our mobile device. We've noticed that unsegmented messages are only serviced and sent every 250ms through the...
Hi, I have made a super hex file and getting the following issue. I have already made a super hex file successfully already but this time getting this error. Does any solution...
Dear friends,
I want to store the sequence nunber in flash, from the case we can know the mechanism.
I found a strange phenomenon that I flashed a serial example( nrf5_SDK_for_Mesh_v5...
Dear friends,
I used my nRF Mesh app provsioning a new device, now, I can export the Json format configuration data of the Mesh network from nRF Mesh app, I want to use...
Hi,
On button press, the button handler event calls the "ble_lbs_on_button_change" function which sends notification to the BLE client.
The value of the button state...
Hello Nordic support,
I am developing a Zigbee application based on FreeRTOS for a device with coordinator role. I was able to add the Zigbee stack and start the Zigbee...
