Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hi, during my tests, I use an NRF52 Dongle with the nRF-Connect app as a USB/BLE interface, but now I need to handle some custom data. I have seen that the dongle uses a COM...
Hi!
I'm working on using the SAADC in 14-bit sampling mode (oversampling set to x2) using nRF SDK 17. The supply voltage for my chip is 3.3V, and I have the reference...
Hi @ all, can anyone here recommend me a suitable chip antenna, preferably one with matching regulatory documents in combination with a nRF52840 MCU.
Thanks and best regards...
I am trying to flash a NRF52832 using the J-link EDU mini in the Arduino IDE but I am having no luck.
I have successfully downloaded... 1. J-Link Software and documentation...
While digging for electrical information I came across :
.63ma using HFINT or 1.58ma using HFXO ?
So I hunted down HFXO to see how to switch between them:
But nothing...
please advice how to add "QDEC_NRFX" to the project configuration of 5340
1. it's not on the default menu config
2. I have tried adding under "ncs\v1.4.99-dev1\zephyr...
Hello
I evaluated FOTA using the http_application_update example. This worked so far until I tried to use my own key for image signing. I created my own PEM-file using the...
Hello,
With nRF52840, I using SDK ver.16 to create a USB HID multiple touchscreen. I need to set up value some HID feature report. Such as Contact count maximum. I have...
Hi,
I want to configure the nRF52840 with Multi-role capability. I will be using the Central role as well as the peripheral role simultaneously. However, i'd like to maximize...
Hello
I would like to use SAADC 2 channels sample at 8K samples \ per second for each channel
based on:
https://github.com/zephyrproject-rtos/zephyr/blob/master/tests...
Hello,
I understand that SES has a built in debugger functionality, but would like to implement debugging on VSCode using Cortex-Debug for a better workflow. I am experimenting...
Hi there!
I'm currently in a position where I'm using SPI0, SPI1 and SPI2 (for ST7735, WS2812 and SD-Card for FatFS) while I need to also be able to use I2C for the Adafruit...
I am using sniffer v3.1.
I have installed the sniffer code on a nRF52840 dongle (PCA100059). When I insert this into the PC it appears as "nRF Sniffer for Bluetooth LE ...
