Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hello,
In my application I use NRF52840 with SDK 16.0.0 and softdevice 7.0.1. I want to add ECDH algorithm to my project using ECDH example in the SDK, but nrf_crypto_ecc_key_pair_generate...
Hi there,
I'm presuming that, when using the s140 soft device (or any of the soft devices), I cannot change the output of VDD to anything and must assume 3V.
I have tried...
PWM frequency and PWM steps resolution are related, we increase one and the other decrease and vice versa, we want high PWM frequency so we have low flickering and we want...
Hi everyone, after months of working with the nRF52840 dongle I decided to buy the nRF52840 DK. I work with the ide SEGGER EMBEDDED STUDIO. I tried to get the blinky example...
Hello,
I can smoothly run the sensor server / client model. I know that I can setup the periodic publication period with the nRF Mesh mobile app and don't have a problem...
I want to configure 32bytes sensor measurement data in advertise manufacturer specific data as follows.
But does not work, please help me.
My environment as follows. ...
Is there demo for video transmission on PCA10056 DK?
it is just video transimission demo. just loopback is ok.
we are using nRF52840. is it possible？ or other platform...
Dear Mr/Mrs,
I am learning to develop an Android BLE apk. I use the nRF Connect apk and Android-nRF-Toolbox to connect with my BLE device.
nRF Connect connect to the BLE...
I have an found a problem where I find FDS has 2 pages labeled as swap, which results in loss of one of the data pages.
my configuration is 2 data pages and 1 swap page...
Hi,
I modified the USB BLE example (nRF5_SDK_17.0.2_d674dde/examples/peripheral/usbd_ble_uart) to sends bytes using a timer timeout as "fixed bytes transactions" or "waits...
Hello,
We have a custom board designed using the ublox Anna B112 module which uses NRF52832. We are using it in open CPU mode and running our custom firmware.
The VDD...
Hi,
For example ble_app_uart, when the peripheral ble rx buffer is almost full, I want to control the central write with response, but I don't konw how to indicate the central...
Hi,
For example ble_app_uart, when the peripheral ble rx buffer is almost full, I want to control the central write with response, but I don't konw how to indicate the central...
