after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
Hi, I have problem. My NRF52832 Dev board is not recognizable by anything. L05 diode is blinking every 0.5 sec. I used Segger - not recognized, Keid again J Flash same story...
Hi,
I'm developing a BLE mesh project using Mesh SDK v4.2.0. I want to change the Tx power of the product in real-time, e.g. from 0dBm to 4dBm, 4dBm to 8dBm.
I've read...
I have an application that is running for a while and then it crashes.
Execution goes to softdevice_fault_handler(), calling it with parameters: id=1; pc=0xf764; info=NULL...
hi all
A silly question here , I am prepare to meet some security compliance , one of them is about delete files permanently.
I wonder how to get this done on nRF51822...
Hi,
I would like to wake the nRF52840 SoC from sleep via a GPIO High Pulse input.
What is the minimum allowable pulse period do I need for it to successfully wake up...
Hello,
I have the following application code (based on the template project from the SDK):
The receive callback is working and I get all the characters from my terminal...
From the datasheet I understand that any pins in port0 can be used as SPI. But I tried using the pins defined in nrf-sdk here and but there is no response. After searching...
Hi!
I am kind of DIY person and have a lots of time in COVID, I am a beginner to Nordic family, few months ago I implemented MPU9250 with NRF52832, I was able achieve...
Hi !
I am working with nRF52 DK to drive the nRF52832 and a sensor of Maxim Integrated.
I am using an older version of the SDK (14.2.0) because i need to modify an old...
Hello,
I was looking at power profiler (just playing with it) and I run it without proper setup on nrf52840DK, after that It seems that dk does not execute any application...
My application is again having troubles with opening an AF_LTE socket. It hangs indefinitely on the call to socket(AF_LTE,...). This code has been running successfully at...
i use nrf51822 and uart project
i need disable only RX when tranmitsion and reuseable when tranmistion complete. i tried
//NRF_UART0->ENABLE = UART_ENABLE_ENABLE_Disabled...
Hi
Do any of the Soft Device versions support the periodic advertising feature which is part of extended advertising and involves AUX_SYNC_IND PDUs? I looked at the API...
I am having a high rate of connection reason 0x3E when connecting two nrf52832 devices together both with only one active connection at a time.
Most of the information I...
