Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
I've recently began experimenting with the HID service and connecting to iOS devices in order to achieve lower connection intervals with Apple products (as described in their...
Hi,
I'm trying to implement a testing firmware for my Nordic nRF52840 PDK where I can send the data generated on an analog input over Bluetooth.
Basically the idea is...
Hi,
After updating the mesh-devices over DFU, we would like to read the version of the application present on the device.
Is there a way, to read this information at runtime...
Hi everyone.
I have to completely deactivate some input GPIOs in my device without any residual current left to avoid damaging the sensor plugged on this pins. I was wondering...
Hello,
I'm trying to use the nRF9160 to make an HTTPS connection to a REST server. Is HTTPS supported? If yes, how to enable / configure HTTPS and are there any example...
Hello,
My system is going to run off a Lithium Ion battery.
I don't need to use the USB Interface on nRF52840.
Is it okay for me to leave VBUS, D+, D- floating?...
There is a period during which advertise packet cannot be received
Central info SDK: 15.3 nRF52840
Peripheral info SDK: 13.1 nRF52832
Running device Central * 2 Peripheral...
When I used light-switch server and client model simultaneously from
https://github.com/NordicPlayground/nrf52-mesh-light-switch-client-server-proxy/tree/master/examples...
Hi Nordic,
I have ported nRF_SDK_15.3.0 to nRF52840. These changes involves USBD. So While initializing pp_usb_init(), I see it is going to some hardfault handler. Please...
Description:
For my project I'm using 3 Nrf52840 DK, two of them as peripheral and the other as peripheral and central. I'm using also an iOS device as central. The two...
Hello,
I bought a Adafruit Feather M0 Bluefruit LE, the Bluefruit LE module is an nRF51822 chipset from Nordic. I connected the Adafruit board to an accelerometer. This...
Hello, i currently evalutate LTE-M for my company and i run into a lot of trouble for starting the test. But at least i have able to do the test
I have cut a lot of code...
Hi Nordic,
It reads in devzone.nordicsemi.com/.../38040
"According to Section 8.23 in the Product Specification a logical high is between 0.7*VDD and VDD and a logical...
Although BUTTONS_ACTIVE_STATE declared as 1, the hal_buttons_init(button_event_handler) yields an event when the input sees a high to low transition in stead of a low to high...
In testing the timers on the dongle, I have made a GPIO pin be controlled by the timer triggering.
So the following has a constant time between edges:
case NRF_TIMER_EVENT_COMPARE1...
I ran into the same problem as other user one year ago (I was using Arduino Studio nad Segger Studio before), now I switched to IAR (as recommended) and as the examples are...
