Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hello,
I'm trying to load BLE UART example on a custom module with nrf52832. I'm using SDK 14.
On the EVK it runs successfully, and I have the following addresses map...
Hello!
I'm trying to perform DFU over BLE using a NRF52 devkit. I'm getting the following error preceded by lots of "Invalid advertising data type" logs:
Traceback (most...
[SOLVED] turn off logging through UART.
Hello
I'm experiencing a strange issue where my device sends a beacon under DEBUG, but does not under RUN.
Due to that I tried...
Hi NordicSemiconductor Community,
I have a problem with the SEGGER Embedded Studio IDE, i want to build my project but i have the following error :
can't open 'C:/Users...
Hello,
I am trying to send out a notification and getting this error code 13313 (in decimal, 0x3401 in hex). Which eventually leads to BLE_ERROR_GATTS_SYS_ATTR_MISSING...
I developing applciation based on nrf51822, sdk11. I have read several posts about using app_timer_cnt_get() and get only 0 value. As far as I understand, this is because...
i want to connect my nfr51822 device to only one phone( that means which phone was connected first). For this purpose i enable whitelists but i create whitelists nothing has...
In timer example in sdk 11, I replace the Timer 0 by timer 1 and timer 2 but the LED did not blink. Can you guys please guide me through this? In nrf_drv_config.h I have already...
I have Keil uVision-5 and loaded the legacy patch. However Nordic NRF51 does not appear anywhere as an option. The Project loads fine and compiles. However, I cannot use the...
nRF52862, SDK 14.2, SD 5.1.0,, Arm GCC (Eclipse)
I have a custom service that is working well when 1 device (phone) is connected. All notifications are sent properly to...
Hello everyone,
I am trying to add new service into ble_app_uart example. I compile successfully. I do not get an error. But the device is not advertising. I can only advertise...
In my plan, I have used NRF52832 IC as the transmitter and the NRF24LU1P+ as the receiver. I have tested the wireless transmission successfully. In order to reduce consts...
Hello,
I get the sources from Thingy Mesh Demo and use the guide to build it examples. Thingy_node build without errors, but Thingy_bridge return the error "too few arguments...
Hi
I am using nrf52832 doing a project and I 'm new to this MCU.
My project concerns sending data from APP via BLE to nrf52832 to config parameters of SPI (data and clock...
