after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am using the nRF54L15 (PANB511 Module ) controller with an ST7789V-based display connected via SPI21 at 8 MHz. Image bin files are stored using LittleFS in external flash...
Hi,
I'm trying to modify the Nordic sample apps included in the ESL Getting Started kit so that the tags first scan for Access Points (APs) so that they can connect to the...
Our IoT device is connecting to 2 different cell towers on the same carrier. Cell tower 'A' has signal of -90dBm, tower 'B' has signal of -105dBm.
The device is mainly attempting...
Hi,
I am using nRF54L15 with SDK v3.0.2 . I am facing an issue while initializing the LSM6DS3 sensor on a custom PCB.
Device Initialization Code:
#define...
I am developing a modbus server application for nrf54L15 in nrf sdk v3.2.3. But I ran into an issue where using MODBUS_MODE_ASCII requires UART_CFG_DATA_BITS_7. The modbus...
Dear Nordic,
The west build system is not acceptable for firmware development.
Firmware != Software. When we create firmware for a product, it must last for years. We...
Hi,
I've reliably implemented a Software Serial library on the nRF52832 using GPIOTE and nrf_delay_us to sample the 8 bits. I tried making this work more efficiently using...
Hi
Is it possible to use the 54dk for programming of our new board with the nRF54L15 running on 1.8V?
Is the voltage configurable on the 54 dk?
Best regards
Peer
I am using nRF Connect SDK (NCS) v2.9.0 for a Matter project.
Currently, the Manual Pairing Code generated is 21 digits long. I need to change this output to be 11 digits...
We follow the youtube video: www.youtube.com/watch
to add battery charging and fuel gauging to our nRF52832 Series project.
It works, but after we enable
CONFIG_PM_DEVICE...
Hi nordic team
I am working with the Nordic nRF5340 SoC using Zephyr RTOS .
Hardware
External QSPI flash:
MX25R6435F
QSPI configuration (DeviceTree):
...
Hardware: nRF9151 DK Modem firmware: mfw_nrf91x1_2.0.4 Carrier: Verizon (PLMN 311480), Band 13 Antenna: External Problem The modem continuously reselects between two cells...
Hi Nordic team,
In the context of adapting the software for our custom PCB I need to make some changes in some devicetree nodes for the net core. Therefore I wanted to add...
