I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Hello Nordic Team I Have tried different usb cables ,and different PC .
all cannot connect to the software .
can you help me to check what has happened .
open log...
I am on the learning curve of nRF9151 and LTE/GNSS.
Trying to build and run the sample app under nrf/samples/nrf9160/location
The errors Im getting are
[00:11:23.476...
Hi, I have upgraded my custom nRF52840 devices from SDK 2.4.1 to SDK 3.0.2. For few days, these devices did connect to existing OpenThread network. But now, all SDK3.0.2 devices...
I used the Bluetooth mesh distributor example from ncs2.9.1, and the Bluetooth mesh dfu can proceed normally. However, when I tried to pause and resume the dfu process, I...
Dear Nordic Support Team,
nPM2100, SHPHLD pin: we would like to connect a pushbutton to GND to wake the PMIC from ship mode. Additionally, we would like to read the pushbutton...
Hello, I am currently designing a custom board using the nRF9151 and I have a question regarding the SWD interface. My understanding is that the nRF9151 contains two main...
I've just spent about 4 hours trying to figure out why a particular build was failing (on nrf9151dk).
Examing the cryptic errors finally revealed that the TFM partition...
We're using the nPM1300 in our designs and we noticed that the charge portion does not appear to keep a battery charged when USB is connected for extended periods.
Our arrangement...
So far we have been using nRF5 SDK v17.1, but we ended up using nRF connect SDK v1.9.1.
However, this compiles too slowly.
I modified main.c and it seems to compile everything...
Hi,
I’m using NCS v3.1.0 and noticed that my application does not run unless I enable:
CONFIG_CLOCK_CONTROL_NRF_K32SRC_RC=y
Without this configuration, the system fails...
HI TEAM,
I am using a custom board and measuring its overall current consumption using the NRF Power Profiler Kit 2 (PPK2) .
Setup details:
Power source: External...
Hi,
We are using the nrf9151 to get GNSS data/coordinates without using A-GNSS, we followed the information in the following page "https://docs.nordicsemi.com/bundle/ncs...
