Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
Hello,
I am attempting to connect to a Wi-Fi network using Exercise 2 from Lesson 2 of the Wi-Fi training in Nordic Academy. However, when I try to connect to the network...
We are trying to configure our device, which is custom based on nrf7002dk for interface certificate testing. The requirements for testing are
Ensure correct Internet Header...
Hello,
Im trying to flash my dev board but im keep getting following error:
Error: One or more batch tasks failed: * 1057707318: [Probe] Emulator error: Failed executing...
Currently, in the early stage of code development with NCS 2.8.0, I'm getting some errors when configuring I2C (TWIM) for a sensor device in a custom board.
The overlay...
On the NRF7001 module there is a "Determine the trim value" section in the documentation. I have followed the "Receive-based approach" to determine the CALIB_XO value. This...
Hi,
I have several deployed devices that have been running for a while, using the nRF Cloud A-GNSS system with the nRF Location library. These devices were successfully...
hi I have recently been developing ncs on vs code. However, I encountered a strange problem. After I clicked build configuration, there was no output in the terminal, except...
Hello all,
I have this problem: when I add support for OTA my bonding information are canceled after power on. Without ota all is perfect.
Example: - Turn on the device;...
Hey there!
I am currently trying to upload a .hex file onto the board to flash it using the nRF connect programmer. But while flashing i get this error:
11:10:10.496...
Hello,
I am currently working on the Exercise 3 – Interfacing with ADC using nrfx drivers and TIMER/PPI sample. I have it operating, however I am wondering what is the proper...
Using NCS 2.6.2
set(PM_STATIC_YML_FILE ${CMAKE_CURRENT_SOURCE_DIR}/configuration/pm_static.yml) in the CMakeLists.txt works well to use static partitions for a appl+mcuboot...
Hi
I have been using the nrf52840 development kit. In the sdk examples I am running the radio test example of pca10056, but in the retarget.c file I am getting this error...
Hi,
I'm working on a testbench to flash product with nRF5340 and nRF52840 chips.
In order to erase/flash both I'm using JLink Base compact and nrfutils CLI. But I have...
