Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hi Team,
I just want to understand how to interpret the SMS received.
I am actually getting a combination of numbers and character for the SMS,here is my log
AT+CNMI...
Hi,
I have been testing unbounded buttonless DFU with BL652 using SDK 15.0 and SDK15.2 and I kept getting Error 8(0x8): GATT CONN TIMEOUT after bootloader is entered.I traced...
Hello! H.W: nRF9160 DK v8.5 MWF: 1.1 NCS: tag 1.2 SIM: Telenor NB-IoT I'm using a modified version of the MQTT simple example for an application that periodically uploads...
Hello,
I am new here and trying to understand flow of every example and bluetooth profile,
so are there any detailed documentations with explanation of snippets of code...
hi，
Requirement 1:Nordic Bluetooth 5.0 is supported on Android 6.0 and above: What interface (hci or else) should be provided by nordic Bluetooth 5.0? How to debug nordic5...
I am working on nrf52832 and SDK V15_3 and Softdevice S132 . I want to enable 2MBPS mode to achieve maximum throughput. I have checked different links in nordic devzone but...
Hi , I succeed to flash the firmware to Thingy52
you can see the attached 2 pictures one is for the nRF Mesh app and the second is the Thingy 52 (Four units) which are ...
Hello,
I am using nRF52840 DevKit, SDK 16.0.0 and SoftDevice 113 v701
I am looking at nrf_bootloader example and want to configure a watchdog that keeps running even...
Hi,
I'm wondering what is a good way of keeping track of when the device is inside the active time window so that the data is being sent at the correct time.
Here is my...
Hi,
I'm working on two projects, in the first one, nRF52832 (softdevice S132 V6.1.0) is used as a slave component communicated with STM32L4+ over UART and the second one...
Hello,
I have been using nRF52840-DK and also nRF52840 Dongle for testing and I found an interesting behaviour when I established my test setup. The RF module acts as an...
Hi All,
We have a product based on nrf52832 that has a custom ble service with 2 custom characteristics.The first one is to send data to the nrf device and the second one...
Hi
I opened the Watchdog in the user application,and do nothing in the bootloader.Then when I use DFU,the CPU reset appears.How can I to deal with it?
And when I upgrade...
Hi
I am looking for some specific contract developer help to build and Android app to update Firmware in devices using DFU and the buttonless service. Obviously there are...
HI,
We are evaluation the nRF9160 in the devkit and we are trying to obtain the values specified in the nRF9160 Product Specefication v 1.1. After following the different...
