Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Hello,
I am using nRF52840, SDK_16.0.0, SoftDevice S140 V7.0.1. I am using ‘ble_app_blinky’.
I am new to BLE certification. I have few queries on BLE Certification...
Hi Team,
I have down loaded the "pc-nrfutil-6.1.zip" from git repository and started the execution by using python commands. while running i am getting some errors.
...
Using PWM control 2.7KHZ buzzer, it can work normally when I don't turn on the broadcast. Every time I turn on the radio, the buzzer seems to blend in with different frequencies...
Hi
Based on zigbee sdk 3.2, add the device to the network, call zb_bdb_is_factory_new() after Joined network successfully, it returns true;
The same is true on zigbee...
Hello,
I am working with nRF52DK, I am trying to implement grouped SAADC for three sensors,
I want to receive all three ADC outputs at the same time on development kit...
Hello,
While working with a bare metal (no SoftDevice or OS) test application to prove code functionalities, I ran out in a weird behaviour that I cannot explain.
I'm...
Hi,
I started to implement the nrf ppm driver into my application. It is a smart connected grand light.
My goal is to smoothly fade the connected power LEDs on, hold for...
Hello,
So I have the following setup. I have an nrf9160 DK board. With the following hardware.
A base shield: https://www.reichelt.com/ch/de/arduino-shield-base-shield...
Hello,
I am using the att_mtu_max_throughput example from SDK 15. I am using an nRF52 as tester and nRF52840 DK as receiver.
I have modified the example slightly so that...
Hi Noridc guys
recently I got some issues about how to know device network state. then I found there was a issue in zb_bdb_is_factory_new() API.
first, i formed a network...
Hi,
I have a problem of crash device after trying to connect my device to the PC via NFC.
The issue is very rare.
I think that the issue occurs because of an assert...
Hello,
I'm currently testing the bootloader with nrf52832 DK on SDK16.0.0 with Segger Embedded Studio. I followed the guide provided in this link https://devzone.nordicsemi...
Hi,
My project is based on SDK15.3 with NRF52840. I have referred to the "writable_ndef_msg" example to read/write the emulated NFC tag successfully. And I can get back...
Hai ,
In my application i should connect parallel connection and peripheral and central part connections simultaneously.
for this i developed from hrs_relay example .in...
Hello,
I'm trying to program a nRF52840 Dongle with the thread MTD client example by using nRF Connect but I get an error saying I need to add a SoftDevice. I thought...
