Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hi all,
I develop program code based on nrf-mpu-magnetomter examples. I code the DMP and complied well . However the program is always stay an error when it starts running...
In my application an nRF52832 acts as a BLE peripheral device which is sending sensor data to an app on a mobile phone. As long as the phone is interested, notification on...
I'm trying to add buttonless DFU to the SDK's template application.
Here is my setup:
Soft Device 6.1.0
Secure Bootloader
Modified Template App (Added buttonless...
Hi,
I am using nrf52832 custom board with s132 to read data from 4 sensors using twi. i have 2 separate TWI with two different sensors on each bus. i am using nrf_drv_tw...
Hi,
I have a question with regards to the system-on sleep current of the nRF52840. This is specific to when using the bluetooth mesh and the nrf_mesh_disable() function...
Hello I am trying to connect nRF52832 development kit to use with Wireless vibration controller store.ncd.io/.../ using mesh module which is transmitting the data to the receiver...
Hi
I'm trying to combine NUS central and peripheral in a single nrf52840. Using SDK V 15.0.0 and softdevice V 6.0.0. Have added both ble_nus and ble_nus_c files and enabled...
I am trying to add Timer2 to light_switch server example. But it fails to compile with a undeclared error for NRFX_TIMER2_INST_IDX. I have set the following macros in sdk_config...
Hello all,
I plan on using the blinking LED authentication in mesh configuration, I have seen the nrf mesh app video where it is done using the app but I want to achieve...
Hello.
I am using the NRF52832 Evaluation board.
If I click the connected board of Device Manager to upload program application, nrfgo studio will be turned off without...
Hello,
I have an existing customer who has products based upon the nRF24L01+.
He would like to upgrade to the newer nRF52x series but is concerned about backwards compatibility...
Dear Nordic
I found a example using nrfx_twim_rx() to scan slaves, I was just wondering if I can use nrfx_twim_tx() to scan slave devices by send zero byte data? I use nrfx_twim_tx...
Hi,
In the BR Bluetooth (not BLE) there is a profile called OPP (object push profile) that enbled sending text messages to mobile phone with out the need to install any...
