Hello:
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions: ...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
It seems to be the case that pstorage_write errors (for example forgetting that it needs to be word-alignment, so 4 bytes at minimum), do not end up in the pstorage_callback_handler...
Hi there
I have never used a nRF51822 device but it looks like a good option for a product development.
Reliability of the link is a priority so the design will include...
I want to connect Bluetooth Smart chip to a weighting scale, read the data and send it to a phone.
Is this possible and what requirements there are for the scale?
The Manual of the nRF518-SDK version 5.1.0 mentions something called nrfprog. Unfortunately the SDK doesn't include it. Unlike what i found on google, i see no nrfprog in...
I have an nRF51822 design that programs fine from the embedded Segger on the eval board.
However, when I try to connect an actual J-Link Base, I can't seem to get it to...
Hi
I have PCA10005 module disassembled from mother board and with VCC_nrf, GND connected to external supply. The chip is able to work with pre-programmed data.
Is anyone...
Hi,
i have a generell question. First i have to say i am not the best programmer, but maybe some one with more experience then me could help me.
Does it make sense to...
Got nRF51422-EK.
Followed instructions and used nRF51 SDK v6.1.0
LED next to the Segger part blinks constantly.
If i build and download Blinky, the LED0/1 do not alternate...
I am developing a platform using C8051F931, MPU9150 and nRF8001. I have re-written the hal code to target the C8051F931 and verified it using the ACI demo test (the echo test...
Hi,
I'm using nrf51822, pca10001 board. I have loaded the uart_example and that worked fine, but using the radio_test_example from Board/nrf6310, that compiled and programmed...
Hello,
I'm new to BLE. I am using nRF51822. Is it possible to modify calling frequency of nus_data_handler() so that I can deal with data coming from BLE faster?
How can...
I see that Digi-Key has two part numbers for the nRF51422-QFAA:
But I don't see any reference to "V2" part number field in the nRF51422-PS document.
What is the exact...
Currently I am set timeout to one second and then on BLE_GAP_EVT_TIMEOUT:
modify data
advertising_init();
advertising_start();
Are there more correct ways...
Hello,
I've connected the nRF8001 module and a light sensor to a microcontroller.
Actually I can read data only when I send a string from my smartphone but I want to...