I am getting following error:
Error in final launch sequence
Error executing step execute method: stepInitializeJTAGFinalLaunchSequence
java.lang.reflect.InvocationTargetException...
Dear Nordic people,
I am playing (6.0.0) with sd_flash_page_erase() and sd_flash_write() , seems to be working ok, Allways happens what I do expect, but I am not able to...
Hi,
Will PAN item #56 TWI: TWI module lock-up be fixed in the Rev 3 version of the nRF51822/51422?
Also would you happen to have a time frame as to when the Rev 3 will...
Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
hi
i read in earlier questions on the devzone that nordic offers to review the schematic and layout as well as perform tuning free of charge to their customer. Is that still...
Hello every!
I am testing FATFS example with nrf5284 PDK .
CLK - P1.15
MISO - P1.14
MOSI - P1.13
CS - P1.12
My micro sd card module work correctly with STM32 MCU. I...
Hi all,
I am Using SDK15, chipset is nrf52810 , In ble_app_uart application i have added the BLE_NUS_C and TWI application code , before this i have added only TWI to ble_app_uart...
This blog describes how to set up SES (Segger Embedded Studio) for use with nRF SDK:
https://devzone.nordicsemi.com/b/blog/posts/segger-embedded-studio-a-cross-platform...
i'm using DFU for my project, it worked fine until devices has been bonded , DFU cannot work again. i checked and find out that after running interrutps_disable() , the devices...
Hello, I am using an nRF51822 chip, configured to run as a SPI slave. The device receives commands from master, sends commands out of the radio, and relays back RF payloads...
Hello,
I've created my own custom model which allows a client to control the duty cycle of a couple PWM outputs which are on the server. My model is quite simple, it just...
Dear all,
We're started studying payment via BLE with NRF52. But i looking for in Nordic website and google it seem a little subject and document. Can Nordic expert supply...
Hello,
I am getting really confused when using te SAADC to convert the read values into voltages.
I have seen that the example ble_app_proximity() uses the following...
I'm using 14.2 SDK SES . I'm trying to send data of sensor through BLE . When i enable Notification in mobile applicaion (nRF connect) i generally dont get any value or garbage...
Hello, I'm trying to port my code for driving spi memory (S25FL256S) from nRF51822 to nRF52840. I'm using nRF52840 Preview DK, S140 and SDK 15.0.0. On nRF51 I used custom...
Hello everyone,
I'm using PDK 52840 as Programmer/Debugger for our target board with nRF52840 chip. We have also other componen which need 2.5V voltage (down from 3v)...
I'm new to both the nRF52 family and SPI, and I'm working on an SPI master nRF52810 (using the PC10040e setup). I'm compiling using GCC and makefiles. I've set NRFX_SPIM_ENABLED...
I try to make a simple project based on a "simple message model" ( https://devzone.nordicsemi.com/f/nordic-q-a/29836/send-and-receive-a-string-via-access-layer ) with Mesh...
