Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
Hello Nordic team,
We are making our own custom project, and we are facing problems in implementing lower power modes.
Reading from the info center, when the DK Board...
When initializing two channels, enter scan mode。After the two channels are converted, the callback function will be entered，Read conversion results。However, the requirements...
Hello
I am following a beginners tutorial on youtube and trying to implement simplest possible example of reading an analog value.
I want to use the nrfx library to do...
Hello,
I am working on a project where I am using 8 ADC channels on the nRF52832. When I run the code the device seems to get ADC values that look correct. But, if I pause...
I have an out-of-tree driver. It has an I2C that is working but also GPIO that are only working with compatible = "gpio-leds" but not with the driver compatible = "st,vl53lx...
On the nRF52840 there were many pins specified as "low frequency I/O only." Does the nRF53 have this same restriction? I don't see mention of these pins in the nRF53 datasheet...
Hello, I am working on application with nRF52833. What is max load current of internal LDO between VDDH - VDD? VDDH is 5V (USB) and VDD is 3.3V. There isn't anything about...
Hi
I am not busy developing an new product with nRF52840.
I want to use the BLE functionality and started with the ble_app_hrs sample application.
I download the pca10056...
Hi everybody,
I am trying install and set up Wireshark, i am in this step:
this is my output:
I think trhe problem is because of pyserial isn't detected, i have...
Hi,
I purchased a BLE dongle with your 3rd party HolyIoT: mini Holyiot-nRF52840-USB-Dongle. It is recognised on Nordic Connect, but not Nordic Programmer (Err msg: DFU trigger...
Dear devzone-team,
could you please tell me where the yaml files (like thingy91_nrf9160_ns.yaml) in the board folders are used?
I could not find a tool which evaluates...
I cannot get my solution to send data through the serial port.
I use the serial application to work on the instance 1.
static void sleep_handler(void) { __WFE(); __SEV...
Hi,
I am testing the nRF9160 DK and used the asset tracker application with the IBasis SIM. Application works fine under CAT M1 network (IBasis SIM is roaming on o2/Telefonica...
Hello
We want modify mcuboot_primary and mcuboot_secondary partition.
mcuboot_primary end_address change to 0x70000 and size change to 0x60000.
mcuboot_secondary end_address...
