Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
[ Problem ]. When communicating with the TestApp as shown below, it is taking an unusually long time to get a response. The problem is that the response takes more than 0...
Hello,
I’m currently trying to flash the blinky code (found in the ‘Getting Started’ section) onto the nordic nrf9160-dk.
The error I’m getting is :
“error: cmake...
Hello,
We have a development team in Kiev, Ukraine.
We see that LTE over nRF9160 is not working there.
Is it possible that LTE over nRF9160 is not supported in Ukraine...
Hello
We are using secure boot loader for DFU and is working great. We were using single bank DFU, but reduced our image size to allow dual-bank DFU. If you could please...
Hello Nordic Devzone Community,
I am developing an out of tree driver for firmware running on an nRF9160. I've made some progress and am getting closer to correctly implementing...
Dear Sir/Madam,
We are trying to lower the low frequency crystal start-up time.
https://infocenter.nordicsemi.com/topic/ps_nrf52840/clock.html?cp=4_0_0_4_3
In the description...
I'm wrapping up a job for a client and we are squashing the last few bugs, but I can't seem to understand one of them. Pin 0.13 of our nRF52840 is pretty simple, just a button...
Looking for wisdom on wiring up the nRF (52833, via Raytac RF module). I'm having a hard time understanding (PS, Hardware Layout) section how the different power Configurations...
Hello,
I have previously created a product using the nRF8001 chip a year ago using a PCB antenna design. At the time the enclosure for the PCB was RF transparent and the...
Hi everyone,
I am getting start with the GPS and LTE connections on your nrf9160dk platform. I have tried all of the samples I was able to find but I get some weird results...
I'm running the Serial LTE Modem firmware and utilizing the reference docs in the LTE Link Monitor Terminal (My commands in yellow, blue/grey text is response)
NCS 1.4,...
is there a sample or some documentation for how to use the USB port to output text from the nRF52840 dongle in a nRF Connect Zephyr application?
It would seem that the very...
Hello,
We're currently trying to update 52840 chip on a similar board such as the 9160dk, that has an external flash in between 9160 and 52840. We want to apply a firmware...
Respected Support Team,
Is it possible to create a BLE Mesh using nRF9160 DK? Alternatively, I also have nRF52840 Dongle and RAK 5010 board which has nRF52840 chip. Can...
Hello,
I am learning how to program my nrf5340DK
I started using the ncs setup but it is too much overhead for me and I wanted to try a more bare setup and I dont mind...
