I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
Hey, I'm new to this so I will need some help. I have custom board with 453-00059 ( BL653ÎĽ with nRF52833 ) and first I want just chip to be seen on my bluetooth devices list...
Hi there,
We are trying to download and install the nRF Connect SDK v1.5.1, which seems to be the latest version on Toolchain Manager.
However, after installation, the...
I'm using the Azure Iot hub example a base for a new project I'm working on.
I've copied the example into its own folder, and can run it and connect my Azure IoT hub.
...
Hi Nordic team,
My dev environment is as follows:
nrf52840 + s140 +SD6.0.0 + SDK15.0.0 + SES + nrf52840-DK
nrf52840 is configured as BLE central with bonding enabled...
Hello,
I'm trying to use PPI over PWM to, at the end of one single PWM period, disable the PWM and switch one GPIO (later, I'll use it for more complex task, but I start...
Hello Everyone!
I am new to nRF boards and still in the learning phase. I want to send some data from nRF52840 to an LCD display through SPI. I am currently using the SPI...
Hi Nordic
One of my customer develop a system with ESB(Enhanced ShockBurst). They employs nRF51802 in their project.
In their system, above 40-50 Tx devices transmit message...
Hi Nordic Team,
I've read some forum discussion about using NAND SPI Flash Chip as external flash storage. These are two chips I'm considering :
W25N01GVZEIG ...
Hi,
We are currently trying to create a small test code to test multiple operator with different modes:
- lte-m1 or lte-nb1
- edrx 0s, 5.12s, 10.24s
- with and without...
Dear Nordic Team,
I recently ported the BLE UART example project for the PCA10056 to the PCA10059 dongle (SoftDevice 113). I added some minor changes like RX/TX pins, GPIO...
Hardware:
Raspberry Pi Zero W
nRF52840 DK running Serial Example and connected to RPi via USB
Custom nRF52840 board acting as a Vendor Model Server x 2
Software...
Hello,
I cannot find a download link for the 17.0.0_9d13099 build of the SDK. Is it publicly available and if not, can a private link be provided? Have some dependencies...
Hi,
I am using nrf52840, need to modify the bootloader to lookup a big bitmap table. But since the table is big, it cannot allocate within the bootloader Rom area.
Is...
Hi
i am using nrf9160 based custom board with zephyr, and trying to build GPIOTE with interrupt for a button, and led finally connect with PPI
i have been trying for...
