Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
We want to physically connect our nRF muRata dk (WSM-BL241-ADA-008DK) to the ST Accelerometer eval board (STEVAL-MKI197V1). We are assuming the connection takes place on the...
I want to used p1.01 and p1.2 and p0.13,so how to defined it.
I do like
#define led0 13 to used pin p0.13 its working but how to define pin P1.01 and all
Hi,
I'm using nrf52840 and connecting to a mobile device.
Randomly - I get disconnections with error code 133 - on characteristics write, on mobile side.
In addition...
thingy91:nRF52840 int64_t convert the value to string in sprintf
Add next line in proj.conf
CONFIG_NEWLIB_LIBC=y CONFIG_NEWLIB_LIBC_NANO=n
If you do the following: ...
Hi, I am developing using nrf52832 and st7735s.
Successfully displayed the lcd screen using the code in \examples\peripheral\gfx
However, when screen clear, text_8print...
I am testing a BLE example that transmits 50 times per second (50Hz) using nRF52-DK(PCA10040) and SDK16's ble_app_uart. After making an arbitrary value into a string using...
Dear All,
We are using nrf52480, we our app is simply scanning for Near By Ble, and if the UUID of a ble Matches it send the data to another controller through Lib Uart...
I'm working on an application with SD card, and I've noticed what I think is strange behavior on MOSI. SD has pullup on every pin (10k), per the spec. Whichever pin I choose...
I receive my nRf-9160-DK but decided to try to get the nRF52840-Dongle working first, Simply walk through installing nRFUtil, following the directions I ended up here: https...
Hi
When programming /NordicSDK/v1.3.1/zephyr/samples/basic/blinky in the cpu_app_ns version, it will not start. It is starting when I compile it as a secure application...
In our application we have an RC network (1kOhm-100nF) on pin AIN1. We charge the capacitor with a defined pulse length and then measure the voltage.
At the desired voltage...
Hello,
I can connect to the Segger JLink plus device using USB but when I try to connect to a Segger JLink pro via Ethernet, nrfjprog I receive the following message " There...
Dear Nordic support,
I'd assume it should be OK to allow nrf52840 to advertise in dual phy mode - primary in 1Mbps and secondary coded phy so that phones with and without...
