I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi, I've been trying to top up my iBASIS SIM card, but after clicking on the nRF Cloud SIM "Buy data" link it fails and generates a system error message (see image below)...
Hi all,
Has anyone implemented an MQTT client on an 54L15 before? I have been searching the web and I have not seen a sample program or anyone talking about MQTT with 54L15...
Hello, I've completed nRF Connect SDK Fundamentals Certificate of Completion but I've noticed a little problem with printk and logging.
When I use build configuration with...
Hello, I have nrf5340dk and AT21CS01-STUM10-T module. This is EEPROM module. I want to communicate with it by 1-wire. The problem is that I don't know how to do it. I looked...
This may be a silly question but for the channel sounding with range requestor sample the numbers following each method is the distance in meters right? I: Distance estimates...
Hello,
I am developing custom hardware based on this DK and am trying to eliminate circuitry that is unnecessary to my application. The DK includes a U20 load switch which...
Hello Nordic Support Team,
I am working with the nRF54L15-DK and testing the Bluetooth Direct Advertising sample application (based on Zephyr). I am measuring current consumption...
Hello,
I am using the nRF5340DK and the PCF8574 with I2C communication. The issue I am encountering is that the function device_is_ready(pcf8574.bus) fails to initialize...
Behaviour:
Declaring a carbon dioxide attribute list with
results in
Using
results in
"zb_zcl_carbon_dioxide_measurement.h" and the macro "ZB_ZCL_CLUSTER_ID_CARBON_DIOXIDE_MEASUREMENT_CLIENT_ROLE_INIT...
Hello Nordic Team,
I am experiencing an issue when attempting to flash a Zephyr RTOS application (v3.0.0) to the Adafruit Feather nRF52840 Sense board using a J-Link debugger...
Hello,
I'm having a serious issue with my nRF52840 board. Here’s what I already tried:
What I have done:
Verified working USB cables (data + power).
Installed...
Hi,the nodic team
I use the system on mode to made the SED device into the low power,I found that in addition to my 5s polling woke up the device, there was another that...
Hi Nordic Team and Community,
I'm working on a project based on the nrf5340_audio application, which I intend to run on the standard nRF5340 DK (the non-Audio version),...
SDK: nRF5 SDK
Board: nRF52810
Softdevice: S112
Hi,
I have a board that has two TWI lines, one has two peripherals and the other has one peripheral connected to nrf52810...
