Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
I saw that the app_timer uses the SWI0. Could you explain what it does and what the advantage is compared to "timer_list_handler_sched()" calling "timer_list_handler()" directly...
Hi, I used the sample code "Master Emulator->2.1.7.8226->Example code->nRFUart"
to develop a new project, and encounter some questions...
we update nRF6310...
Hello,
How many RX buffers are in S110 SoftDevice? I know there are 6 TX buffers (so you can send 6 packets per Connection Interval).
How is it on receiving?
Is it e...
Hi,
I need to connect nrf52833 (BM833 module) with host controller. what are all the interfaces needed to communicate with host controller? help me out in this.
Kindly...
I used 2 channel saadc, channel 1 and channel 3.
Maybe in the first few minutes, it's done ok,
p_event->data.done.p_buffer[0] is belong channel1 adc value
p_event->data...
Hello,
We have integrated the FATFS example as shown in the usbd_msc example project into our own firmware application. It works perfectly on the nRF52840dk and when we...
Hi,
I want to check time line of my project using segger SystemView.
- SDK 16.0.0v
- ESB example
- nRF52832
When Start recording, "Could not find RTT Control Block...
Hello Team,
I want know how to use RESET pin [pin. no. 21] as a GPIO.
I followed below thread but it not work for me!
devzone.nordicsemi.com/.../disabling-pin-21-of...
Hi:
What's the marking on the nRF24-LU1+?
Marking exactly "nRF24-LU1+" or any chance marked as "nRF24-LU1" instead? Your big assistance & prompt feedback is much appreciated...
I am using NRF52810 in : In advertising mode not able to erase or write to flash sd_flash_page_erase. hungs up via processing commands from nrfx_twis_state_machine
Hi,
I'm developing a custom application starting from ble_hrm_freertos application. When NRF_LOG is enabled there is no way let the chip in low power consumption. I found...
Dear Technical Support,
I have faced a problem debugging firmware on our custom board based on Nrf52811. We use j-link EDU and Segger Embedded Studio as development tools...
Hello Nordicsemi community,
1) manual build of mcuboot - When trying to build the mcuboot for nrf5340 via the mcuboot/samples/zephyr via the west build command, the build...
HI , nrf52832 with SDK v16 on that using this nus example location below mentioned
examples\ble_peripheral\ble_app_uart\pca10040\s132
in this example, didn't change...
Hello,
I have recently received the nrf5340 development kit as part of the Hackster contest.
I followed the webinar and to get started
1. Connected board via micro USB...
I started a new ticket since I got a solution to not connecting to the cellular network. Apparently the iBasis sim is not working so I acquired a Hologram sim. I now can connect...
the code yesterday when debug can pop out voltage ,i do not chang anything today ,the code can not run the location ,i make three breakpoints in code and debug ,the code only...
First day using the new dev kit nRF52833-DK. Connected it up following the instructions on nordicsemi.com/start52833dk - computer won't mount the JLINK removable disk so I...
