Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
We are in an environment that is highly security conscious. As a result any third party software cannot be installed unless it is white-listed with Symantec, our end point...
The NRF51822 datasheet (section 9.4 and 9.5) says the CTAC and CTAA WLCSP packages have a normal height of 0.35mm. The datasheet also says the CEAA WLCSP package has a normal...
I am developing BLE applications with nRF52840 DK and the Thingy 52. My application needs to use the entire 31 bytes available for data in BLE protocol. So I don't want to...
Hi!
What would be the best course of action if I have a connection like this:
Android device (without Bluetooth support) -> RS-485 -> UART -> Main nRF52840 DK + other...
Hi Nordic:
I want to make .a library, i use gcc to make .a library. And add .a library to my project. when i build the project , show build failed and the message is ".a...
Segger Embedded Studi, SDK 15.2, Windows 10
Nordic NRF52DK PCA 10040 1. 2 .4
Hello again everyone, I have gotten farther with my previous issues of not being able to access...
Hi All,
I am new to embedded low power design and would love some tips on power saving steps and tutorials for the nrf52832 device.
I am trying to understand the power...
Hi,
for a project I need to perform a DFU Update over BLE. After I prepared the bootloader (generating public and private keys and building it), I prepared the update packet...
Hi, I develop device for custom location service based on BLE. Now I'm working with nRF52 Development kit v1.1.0, nRF52832, SDK v15.0.0.
I have a problem with adding 16bit...
Hi,
I wonder if all Tracedata[n] pins are needed for debug? That would make five IO:s useless for other functions. Or is it possible to use 1-bit mode or something similar...
I wnat to set P0.30 and P0.31 for I2C CLK and SDA. nrf_drv_gpiote_out_config_t out_config = GPIOTE_CONFIG_OUT_SIMPLE(false); err_code = nrf_drv_gpiote_out_init(30, &out_config1...
I set up my nrf52 self board with internal LDO using reference schematics with internal LDO setup.
Im entering the power safe mode using __WFE instruction
Also i did...
1.I used Timer2 Capture function Time Frequency is 1MHz. Picture1 Current counter should be 33330. Picture2 Current counter should be 5000. Picture3 Current counter should...
Hello,
I am having an issue with setting up the event generation timing on the nRF51822. Long story short, I am configuring Timer/Counter 0 to generate an event every 50ms...
Hello,
I am using NRF51 DK for developing an application. I tried running the default SPI example in the SDK 12.3 which uses the spi and spis example. The location of those...
