Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
I saw that the app_timer uses the SWI0. Could you explain what it does and what the advantage is compared to "timer_list_handler_sched()" calling "timer_list_handler()" directly...
Hi, I used the sample code "Master Emulator->2.1.7.8226->Example code->nRFUart"
to develop a new project, and encounter some questions...
we update nRF6310...
Hello,
How many RX buffers are in S110 SoftDevice? I know there are 6 TX buffers (so you can send 6 packets per Connection Interval).
How is it on receiving?
Is it e...
My sensor is off-standard,so I have to use gpio to read and write my sensor.
Gpio IIC will take about 0.5ms to get data.
My app need send data every 7.5ms,it seems that...
Hi, i am trying to port my project based on the matter light bulb sample to a PAN1780 module which also uses the nrf52840 I used before.
When building I receive this error...
Hi, I'd like to trace the Bluetooth behavior of the nRF Desktop sample post-pairing. I have an nrf52840 dongle running the sniffer, and can observe advertising packets. Could...
Hi
We have a legacy product with around 100.000 active devices. We still need to distribute new firmware releases, and we are using the "Chained DFU" app for this purpose...
Currently, my environment uses a mobile network shared through a wired connection to an RT-AX57 router. I am working in the VSCode environment using SDK v2.6.1. Devices: Nest...
I am trying to connect a nrf5340dk to a Jetson. For now I am testing with an Arduino. I am trying to run the CanCounter example with a device tree overlay file. Also I would...
Hi,
I tried to implement the CAF LEDs module as described here . But when added the Kconfig variable CONFIG_LED_PWM =y I got the error message "CONFIG_LED_PWM was assigned...
Hi,
I was developing on Visual Studio Code earlier, and for some reason, I cannot build pristine. If I try to edit the build configuration, it never loads, and if I try...
Hi,
we are trying to make the NORA-B126 (specifically its onboard LNA) work with nrf sdk 2.3.0 by modifying the 5340dk dts and defconfig files as specified in the NORA-B1_SIM_UBX...
Hi there,
I'm working on NCS2.7.0 and nrf52840.
I used the chip-cert to generate custom DAC, PAI, and PAA with VID = 0x1234 and PID = 0x5678, then placed the...
Hi there,
Thanks for helping. We are using the nRF52840 DK along with the Power Profiler Kit 2 (PPK2) for power measurement. We are encountering periodic power spikes during...
Hi, we are designing a factory acceptance test (FAT) jig for a custom board containing an NRF9160 SiP. We are testing more than one thousand boards, and probably more than...
Hello
We are using a slave processor with AT command to communicate with the nRF9161 . This is working without problem
But we are initially using the Quick Start 0.2.7...
Hello,
I'm using nRF9160 as a HCI host and nRF52840 as HCI controller (nRF52840 config is based on HCI lpuart example). My application receives data over Bluetooth using...
We have two cases where the modem has downgraded itself from version1.3.2 to 1.3.1.
1. In the first case, due to water ingress, it appears that the reset pin has been toggled...
