Hi,
I use the nrf51422 chip.I want to know if the ANT establish link between chips,where can I get the matching configuration (like device type、channel ID).I mean is...
Is there a way to recieve more than one write callback for a given characteristic, per radio session? It seems like I can rx 1 time per attribute per radio session and tx...
If it can work with iOS blue setting will be better
I need some reference to dev hid device in IOS
but I can just find my device ,connect ok but not work.
I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
This is not a ticket!
This is a project that I built. It uses the nRF52 to control a neopixel (ws2812b) via I2S over BLE using a custom mobile app built using the...
On SDK16.0.0 + Mesh SDK 4.1.0
I know that oversampling when using the SADDC in scan mode on multiple channels does not work because the buffer gets all out of order.
But...
Hi,
as describe in the title, we are getting a mesh assert when trying to remove all suscibtions from a model.
it is kind of hard to reproduce because this command is...
Hello,
I am testing direction finding over nRF5340 PDK.
I didn't have antenna array yet, but I think that's equivalent to signal received at 90 degree.
I have two questions...
Hi,
in SDK/components/libraries/timer/drv_rtc.h, there is some preprocessor define provided to select the RTC module (0, 1 or 2) used by app_timer2: APP_TIMER_V2_RTC0_ENABLED...
I want to trying to the HCI Command (DTM Mode) of CTE (Constant Tone Extension) feature for SIG RF Pre-TEST,
The nRF5 SDK v16.0.0 (latest version) is ready for CTE feature...
Hello,
So I am trying to build the ble_app_blinky_c example of SDK_14.2 to work for nRF52810 but encountered problems.
I used s132 v 5.1 for my softdevice by following...
Hi,
We have a project want to fixed "access address".
We want to fixed "access address" in every BLE connection (52840 as master)
Do you have some of API to assign ...
Hello, i made my own working NRF24L01+ using the reference design from the datasheet and it worked quite well. But i needed some more range so i wanted to add PA+LNA module...
[Google Translated]
Good day. I am new to application development. At the moment, I managed to implement a connection to nRF52832 using BLE via UART on an Android device...
Hi,
Greetings !
I want to take continuous 40 reading of adc by varying time interval between readings based on RPM value. I want timer interval resolution from 6 Sec...
Hi,
We are using nRF52840 on our product. Since we want to support USB function, we connected VBUS pin of the chipset directly to the USB connector.
We would like to know...
Hello there,
How can I activate long range (coded PHY) in IoT examples, especially in TCP Client application. I've searched that forum and all of entries discussing about...
After receiving my Thingy:91, all was working as expected until I found that the included 10MB of data on the iBasis SIM had been used up and the device refused to connect...
