I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
We have a custom board with nrf9160, ncs 1.2.0 and modem fw 1.1.1. We experience strange behaviour with the GPS: As an example,on units with 30 min fix intervals, we experience...
I added the commissioning part from the nfc_meshcop example to the mqttsn_sleepy_subscriber example. I tested the nfc_meshcop exaple and worked, so the border router part...
Hi,
I have developed a project of mine based on the nRF52840 DK and now I want to place
the nRF52840 chip on my custom 2 layer PCB board but I think that it might be very...
We still have some Problems to use the Supl client Library, to test it we use the normal GPS example and seems like the connection is available with NB-Iot settings. We are...
I have a product which uses the nRF52840 SoC that will also have NFC functionality. The housing of the PCB is sort of forcing a custom design for the NFC Antenna.
We need...
Hi All,
I am using Segger ISP1430603E board to program my nRF development kit. ( ISP1507AX )
With SES I am able program, debug the application.
I would like to program...
Hi there,
I am wanting to develop a custom PCB for the nRF52833 SoC. I am basing it off the nRF52833 DK! As such, most of the schematic labels are identical.
For our custom...
Hi,
When I do a secure DFU (screen dumps pasted ), it failed with error code 0x8005. It worked on WIndows 7 PC.
//==================Linux System Report
# nRFConnect...
where is UARTE configuration in sdk_config.h? According to this doc (for SDK15.3/UART):
infocenter.nordicsemi.com/index.jsp It seems I can follow the steps to enable UARTE...
Hi,
I am using 2 PCA10040 kits provisioned in the same group. I want to change the payload on button press event from client side which I can receive on server side. How...
I have a nordic kit but the dongle or the kit is not recognized by the computer. Is there a driver that needs to be installed before this will happen? I've already installed...
Hello Guys,,
I am trying to migrate my project form keil to segger embedded studio. My product is based on sdk 12.2.0, using softdevice s130 on nrf51822. I searched for...
Hi,
we have two nrf52840 which shall connect very quickly.
The scan+advertise cycle is very fast (we have no bootloader). After switching on the peripheral it is recognized...
