before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
I saw that the app_timer uses the SWI0. Could you explain what it does and what the advantage is compared to "timer_list_handler_sched()" calling "timer_list_handler()" directly...
Hi i am doing a prosject to get notification on cell phone when i get mail in my postbox (postbox outside the house) I am using a nRF51 dongle, and want it to connect to cellphone...
Hi! I'm working on HID mouse example on SDK 13.0.0. I'm supposed to use this as a low power media button control. I've done a few modicifations on the code for power optimizations...
I know that few companies choose to use NRF528001 with a separate microcontroller like Fitbit.
I would like to know why would they do so instead of using an NRF52 chip that...
Hey,
I am using a nRF8001 with a STM32L051 as an application controller.
After resetting the nRF the RDYN pin goes low, as expected. Then I'm setting the REQN line LOW...
Hello all,
I have a Nordic Thingy 52 board, and I have download the Thingy 52 SDK, I can debug it successfully.
But after I debug it , or download it, the board runs with...
We have an application with FreeRTOS. If we do not initialize softdevice, the freertos interrupts tend to come in at a very very slow rate. I know that softdevice does clock...
nRFgo Studio displays a "Enable reset pin" option on the nRF52 DK but does not display this option on our custom hardware; we use a Segger J-Link for programming the custom...
Hello,
I would like to know the CALIBRATEOFFSET function in detail.
Could you disclose the part of source code on this CALIBRATEOFFSET function?
Best regards,
Kiyoshi...
Hi,
In production line, I was supposed to do BLE test using DTM with UART interface and MT8852B from Anritsu.
However, the antenna is specifically tuned for plastic...
Hi,
i was about to solder my PCB that contain an nRF52832 and i've noticed that i didn't have C9, C10 capacitors.
C10 is the 1uF decoupling capacitor for the 1.3V regulator...
Hi, I'm using nrfUtil 10, which is a bit old. I'm trying to generate an init packet for DFU but the tutorial was for newer versions of nrfUtil only and a lot of commands appear...
I tried to compile the sd card example from the fatfs library. But it didn't work.
Can anyone tell me more about this errors?
NRF_BLOCK_DEV_SDC_DEFINE(m_block_dev_sdc...
NRF52DK (PCA10040) - SDK14 - Arm GCC (using Eclipse) - S132 5.0.0 Soft Device
I had a custom service set up in SDK13 using the tutorial here .
I am migrating my project...
