My sensor is off-standard,so I have to use gpio to read and write my sensor.
Gpio IIC will take about 0.5ms to get data.
My app need send data every 7.5ms,it seems that...
Hi,
My android Proximity application fails on service discovery only for the very first time it connects with the devices(nrf51822 evaluation kit with sdk 5.2.0). Actually...
Has anyone converted the app note AN34 DTM Python script to C# or C/C++ ?
The Python DTM script is works OK with the setup specified in the app note AN34 figure 2, which...
Hi,
I have a serious problem, when I use uart of NRF51822 QFAAC0 to receive data from another MCU, I found that it will lost one bit at same position everytime. my SDK is...
Hi,
I just started to interface the lcd display with nrf51822 evaluation board. The display i'm using is, spi compatible, 18" tft (160x130) from tiny lcd. I took spi master...
Hi,
We are using the nRF905 device in an application where it needs to switch between auto-retransmitting and sending single packets, due to it communicating with several...
Hallo,
I'm using Segger Embedded Studio to program nRF52840. In the Nordic nRF5_SDK there is the ble_app_uart example using S140 softdevice, which is running well. Now I...
I am trying to measure the current consumption on nRF52832 PCA 10040 2.0.0 with PPK 2 (PCA 63100 1.0.1).
I have cut the SB9 and connect the PPK as the picture:
as shown...
Im a bit stuck here.
I have the following code, trying to communicate with a flash memory:
Overlay:
code:
I get the following error message:
error: ...
Dear Nordic, I have developed an application for nRF52811 on nRF52840-DK.
For this i have referred examples -> peripheral -> template_project.
I have followed https...
I just fired up our most recent custom boards with nRF9161-LACA's, and tried to compile modem shell application for RTT.
I noticed the RTT is disabled because HAS_SEGGER_RTT...
I am working nrf52840 with bg96 modem, i have configured quectel_bg9x.c driver to communicate with bg96 modem from nrf52840.
can you provide a sample application on MQTT...
Hello,
I'm experiencing an issue integrating a freestanding Zephyr module with the sysbuild system. The module defines custom boards and projects. When I use the...
Hi
We are the Manufacturer of Smart lighting
We have start new project" Cellular gateway".
We are evaluating the nRF9160 Dk board .
During this we found issue . it...
Hello,
I have 4 nrf52840, 3 act as peripheral and the last is the central.
The peripherals are identical hardware with various sensors using the same FW. I order to...
SUMMARY
Attempting to OTA the nrf52840dk over BLE.
I was able to perform most of the steps in this sample: https://docs.nordicsemi.com/bundle/ncs-2.1.4/page/zephyr/samples...
I have a photodiode, and under indoor lighting conditions, the reading on the oscilloscope is about 150mV. When I connect it to an Arduino Uno or Adafruit nRF52840 Sense,...
I built an application on the NRF52 Development Kit.
I was using the old NRF serial application with the retargetio.c file to push data out through the serial port.
I...
I have been looking at BLE with the Nordic products from the perspective of someone who gets a hand wave of an idea and moves forward. I have developed Nordic firmware but...
We have been able to enable coded phy with PAWR using
```
struct bt_le_adv_param *params = BT_LE_EXT_ADV_NCONN; params->options |= BT_LE_ADV_OPT_USE_IDENTITY | BT_LE_ADV_OPT_USE_NAME...
Hello,
I'm using nrf52840 DK to test 1khz tone. The nRF Connect SDK version is v2.6.0.
I put a pcm raw data array of 1khz tone in the code and used i2s write to send the...
