Has anyone converted the app note AN34 DTM Python script to C# or C/C++ ?
The Python DTM script is works OK with the setup specified in the app note AN34 figure 2, which...
Hi,
I have a serious problem, when I use uart of NRF51822 QFAAC0 to receive data from another MCU, I found that it will lost one bit at same position everytime. my SDK is...
Hi,
I just started to interface the lcd display with nrf51822 evaluation board. The display i'm using is, spi compatible, 18" tft (160x130) from tiny lcd. I took spi master...
Hi,
We are using the nRF905 device in an application where it needs to switch between auto-retransmitting and sending single packets, due to it communicating with several...
This is not a real question for support. It's more a success story i'd like to share with you!
Our company develops firmware for various customers on a lot of different...
Hi all,
What is the maximum data rate for the nRF24AP2 when using the Synchronous serial interface?
I cann't see it in the datasheet.
Is there anyone can answer me...
* Query on Combined DFU : 1. nrfutil version being used : 2.3.0 2. Followed nRFUtil for Generating DFU packages from -> https://infocenter.nordicsemi.com/index.jsp?topic=...
Hi! We're working on a testing Jig which should test our units in production.
One of the tests I'd like to make, is measure the current draw on TX at max (8dBm). I would...
Hello,
we are currently developing a new prototype board with the nRF52840-chip.
In order to figure out the best performance for our bt-antenna we decided to plan our...
i want to use orientation interrupt of bmi160. but i don't know how to read interrupt data. I wrote it after looking at the data sheet, but I want you to let me know if there...
I'm trying to get Thread working on the nRF52820. It seems that neither the "nRF5 SDK for Thread and Zigbee" nor the "nRF Connect SDK" support it (yet?), but instead require...
Hi,
I understand that when a peripheral is advertising it is also waiting for connection/scan requests.
Does those requests and responses sent via the same advertising...
Hello!
I'm trying to send a mcumgr packet over uart between the nrf9160dk_nrf9160 and the nrf9160dk_nrf5284.
To do this I have a SMP srv and a shell on both MCUs.
...
How do I get following combination to work:
Nrf connect 3.6.1 power profiler with PCA10040 v1.2.1 + PCA63511 v1.1.0 with external power supply and external DUT
The same...
My error messages in Segger studio are messed up (shown below). Everything else is fine. Can I change the font or something?
[m[K'[01m[Kdev[m[K' undeclared (first use in...
Hello, I have a 52832 using SDK16.0.0, that acts as an advertising peripheral (anyone can connect to it), and as a central, connected with 1-1 bond to a peripheral (a 52811...
Hi, using the Nordic power profiler 2 (PP2) kit to measure the current draw of my nRF52833 DK. I have followed the instructions to setup/prepare/wire the PP2 to my DK and...
In the task, when I do a TWI read via nrf_drv_twi_rx(), in the second iteration of the thread, the driver function returns NRF_ERROR_BUSY.
Is it that the driver takes longer...
I've built a custom board using nRF52832 which uses SDK 16.0.0 and softdevice version s113. A part of application is audio streaming/ decibel calculation and transmission...
Hall Mr. Nordic,
I'm sending a 16bit payload with 51822.
The receiver 24L01 is receiving all perfectly. The receiver 52840 is loosing the first two bytes ...
nRF51822...
