I have a working project where pin 16 is configured as a low-level interrupt source.
it is working well with SDK 15.3
after porting to SDK 17.0.2, it is not triggering...
Hello Nordic Support Engineers and fellow developers ...
Just a note to thank everyone for help via this forum. I started very inexperienced with Nordic SDK a year ago and...
Hi,
I recently purchased a thingy91 for a project. I'm trying to follow instructions from a Nordic youtube video ( https://www.youtube.com/watch?reload=9&v=xQ7hDzRULJQ ...
I have a nRF5340PDK, Now I want to know the lowest power consumption of this chip in different condition, such as adv, connect, sleep. But I am not sure how to config the...
Hi, i am using:
-nRF 52 DK
-nRF 52832
-Sensor of Maxim Integrated
-SDK 17.0.2
I have some problems in handling the I2C through the nrfx module.
This is my ReadByte...
Hi, I have a set up consing of an nrf52840, a Raspberry pi and a Linux workstation, which communicate over IPSP following the IPSP sample from Zephyr OS. The nrf52840 is a...
I want to use the nPM1100 to battery manage, and supply power to the nRF52xxx - along with a heavy duty load ***directly across the battery***, so that full battery voltage...
Hi,
I'm running the experimental example: 'ble_nfc_pairing_reference_pca10400_s132' using sdk17.0.2 (and 17.1.0).
After I installed the micro-ecc following the guide on...
Hello
I am evaluating design of wireless communication in power supply with nRF24L01P , and I have 4 questions.
1.I want to know the Mean Time Between Fails (MTBF) and...
I'm using softdevice s140.
My power comes from a CR2032 coin cell.
My board has a 1.8V LDO (Toshiba TCR3UM) because my temperature sensor is calibrated for 1.8V (TMP112B...
Hi,
Looking at the source code for nRF Connect SDK v1.7.0-677-ge3c356ec8 and SDK For Mesh 5.0.0 I can't find any indication that the following section of the Mesh Profile...
Dear Nordic,
we are devepoling FW based on nRF52832, SDK 17.0.2. We have 2 devices:
BLE Central with SD S332
BLE Peripheral with SD S112
We setted up an open BLE communication...
hi all,
i am using sdk v8. i want to on rtc when button is pressed and i want to off the rtc when it is released.
i am using bsp_handler only for button press.
PROBLEM...
Hi,
I am a little confused between GPS and AGPS sample code provided by nordic. can you help me to understand it?
I just want to send GPS and accelerometer data of thingy91...
I am trying to build the ncs example direct_test_mode with the nrf52840dongle and I am running into these warnings on build in vscode:
I do not understand what it means...
I tried using the ble nus with throughput using the example from https://github.com/LeoHJX/ncsExp/tree/master/app/ble/throughput_nus . However i kept getting an error on the...
Hi all,
I am running an cts example which is asking for bluetooth dongle is there a way to avoid bluetooth dongle,
or can u suggest any example for current time service...
Thanks in advance for the help.
I connected my 9160DK (V1.0.1), downloaded the SDK programmed img_app_bl\serial_lte_modem_2021-10-20_d29f1dde.hex and tried to follow the...
It would be convenient in my design to use a single PCB design in 2 different roles. 1. As a continuously-powered rechargeable battery device, with USB charging. 2. As a USB...
Hi,
We are currently trying to flash the BLE connectivity firmware on the nRF52840 USB dongle using the nrfutil dfu usb-serial utility.
OS: Ubuntu 18.04
Command...
Hi,
I have been quite active recently, because I had a whole lot of trouble learning to use the nordic tools. I just recently managed to merge two deferent projects one...
