Dear friend I checked the data sheet of 52820 and I didn't see any LPCOMP peripherals. Check the data sheet of 52832, there are LPCOMP peripherals. Comparing COMP and LPCOMP...
Hi,
I am working on internal flash nRF52832 merged with twi sensor, my sensor function will return a string . How to assign the string to the my_data.p_data . i am getting...
Developing on the nrf51822
Have working code for the nRF52840 Dongle using the pc-ble-driver therefore all Bluetooth work is done using sd_* calls. The PC provides easy...
Hi ,
I would like to know if a matching network is needed if I am only using a single external flex antenna for both LTE and GPS using a RF switch between them and a uFL...
I am a student interested in Nordic.
My coding skills are very poor.
So I want to get help.
I want to use the vl53l1x sensor in nrf52. (My ultimate goal is to measure...
Hello,
I am working with the nRF52 Development Kit and the Enhanced Shock Burst Protocol. I am trying to send Data from one Development Board to the other with static Payload...
I want to encrypt advertisements using aes-ccm peripheral present on the nrf51 board. I am not using softdevice, instead I am generating my own packets and transmitting them...
Hi,
I want to check if the FW is properly loaded into the chip and the chip is locked. Reading APPROTECT hangs the chip even if SD is not enabled. I assume APPROTECT is...
Hello,
I work on application (written in C, compiled with GCC) which use pc-ble-driver 1.0 and nRF51822QFAC with the ble_connectivity (S130 v2.0.0) as BLE Gateway. I need...
Hi,
Anyone around that has good experience designing nfc antennas?
I'm in need of a pattern that is about 50% the size of the flex that comes with the nrf52 kit.
Doable...
Hi @ all.
I have a strange behaviour that I can't get rid of. But first some specs:
SD130 (2.0.0)
nrf51822
SDK 11
custom board
I have an application...
Hello, I'm south korea student in dongguk univ.
I use keil uvision4, nrf51822, s110 softdevice I need check the run-time.
ANd i like to check the runtime.
So i used "app_timer_cnt_get...
I am nrf51822 QFACA1 chip with s130 softdevice using nordic_sdk_11.
ble_connectivity example was not working and i am unable to do a scan from my application board.
Currently, it using the I2S at nRF52832.
I want to play the wave file,But can not play well.
So, I ask you for a check because there is the following question.
[Question...
Hi all,
I have just buy a product use nrf51822 chip, I tried to find out SWIO and CLK pin out to flash but can not. Device only has RX and TX pin for Uart function, so I...
Hi.
I use nRF52 and I want to use DFU.
I want to make init packet because DFU need it.
To make init packet,
need master control panel.
I want to know how to get...
Hi There,
Is it possible to modify the number of BLE frames per connection interval (CI)? We are using nrf52832s and are only seeing one master request and slave response...
Hello,
can anyone tell me something about the security level of the connection like it is made in the Heart Rate Sensor Example. Is the connection encrypted or can everyone...
Hi all, I'm working on SDK11.0.0 experimental signed bootloader, I stored device type and device revision in uicr register now I need to update my bootloader through dfu and...
hi everybody.
Please help me on this
I use nRF51822 as iBeacon with ble_app_beacon in Nordic DK in below state:
only advertise in iBeacon mode
interval = 100...
