I have a PCA10059 dongle. I have inadvertently configured pin P0.25 as the sleep debug pin and I use active state 0 as I am using off board LEDs with reverse logic. This means...
If you're working on a product that requires you to show and translate GATT Attribute (Service, Characteristic and/or Descriptor) UUIDs to Strings to the user, it's likely...
Hello,
We have been trying the sendNotification call and after getting a success log we are not able to send a second notification. I'll copy the snippet of code that we...
I have a firmware developed on the nrf52840 development board. When porting it to nrf9160, a lot of errors were reported. How can I use the LOG output function on nrf9160...
Hi I would like to ask you for advice on how to solve my problem with Ble and the timer I am trying to add a timer to examples\ble_peripheral\ble_app_uart the timer works...
Sir,
We finally added WIFI to NINA B302, using a NINA W102 coprocessor!
https://github.com/khoih-prog/WiFiNINA_Generic
Please, enjoy!!!
Here a portuguese BLOG...
Hello!
Does anyone know of a library for the I2C LCD 16x2 display? I found the library by lovee, https://devzone.nordicsemi.com/f/nordic-q-a/23401/nrf52832-connect-with...
I am using the nrf54l15-dk. I had a look at the datasheet and it shows that a watchdog reset does not reset the GRTC. On my code, I tested that and I see that GRTC resets...
Issue: It appears that whether or not TLS is used by an MQTT client MUST be configured at compile-time. An application with the Kconfig symbols enabled to allow TLS to be...
Hi Nordic S .team,
Could you please help me analyze the following inconsistencies, and also provide the requested documentation?
I’m trying to interpret the AuTerm messages...
Hi Nordic Team,
I am working on matter-based product development using nRF54L15 and looking for machine learning support for the same SoC. Can you please confirm if machine...
Hi
I tried to find this file in the SDK folder and it does not exist. I do have it enabled in the stock sdk_config.h
mike@slavebox armgcc % find /Applications/nRF5_SDK_17...
Dear Nordic team,
i am stilll struggeling with the GPIO set-up in system off mode. It seems, that both GPIO_INT_EDGE_TO_ACTIVE and GPIO_INT_LEVEL_ACTIVE are working fine...
I am getting started with the nrf52840 dk, and I am unable to clear the flash with the Quick start . Here are my logs: 2025-09-24T02:11:29.285Z INFO Initialising the bundled...
Hello,
I'm trying to connect an SPI device on the nRF54L15-DK kit. The Nordic support page says it needs to be configured using the board configurator , as seen in the screenshot...
Hello,
I would like to ask if it is possible to upload a program to nrf7002_DK where it will be possible to select Wi-Fi STA or AP mode? I tried to connect it, but the compilation...
So I have a timer interrupt setup which triggers every 1ms in the interrupt I give the semaphore with The interrupt triggers correctly as seen from logic analyzer this should...
Hi,
I’m working with the Matter Door Lock sample in NCS 3.0.2. With the default PRODUCT_ID = 0x8006 , everything works as expected: commissioning to Apple Home and Google...
Getting a Precise data bus error - BUS FAULT, when sending a http POST request to an https sever over tls. Cannot decipher the exact instruction address as on enabling CONFIG_DEBUG_OPTIMIZATIONS...
Hi, I have a device using nRF5340+nRF7002. I am storing multiple wifi credentials and using auto connect. I have some questions: 1. Using auto-connect, how does the SDK/wifi...
through RTC i am trying it but it is not happening can you give any propre example one for the sleep mode enabling and wakening up from the sleep mode.
Hi,
I'm using the peripheral_hids_mouse example from NCS v3.0.2. What's the correct way from SC(Secure Connections) to enable Just Works pairing ?
Thanks!
