I have a project where we have 2 nrf51 that need to be time synced with eachother.
The problem is they are placed on the body one on the back and one on the chest of a person...
on the page
https://infocenter.nordicsemi.com/index.jsp?topic=%2Fsdk_nrf5_v16.0.0%2Flib_crypto_backend_micro_ecc.html&anchor=lib_crypto_backend_micro_ecc_install
step...
Hi,
In our one of the product we are using Nordic nRF52840 MCU and we compiling this application code in windows with SEGGER Embedded STUDIO IDE Version 4.30a and Tool chain...
Hi,
We made an online course on Bluetooth Low Energy, includes BLE Fundamentals & Architecture, step by step implementation of Environment Sensing service development...
Hello, I am using nRF9160 PCA10090 DK. I want to make my board as central device and scan for all nearby BLE devices and display its rrsi value and device id on a terminal...
Hi Dears,
I have submit a issue for about two weeks but no response yet, would you please help me for handling it?
The link is https://devzone.nordicsemi.com/f/nordic...
It's really really really annoying that the DevZone contains so much outdated infomations and deadlinks .. especially after moving to the new website !!! :-(
We are implementing on nRF52840 with latest NCS version the following code:
The nvs_init() function is halting due to an error at flash_sync_mpsl.c within nrf_flash_sync_exe...
Hello,
We are working on the nrf52840 custom board in that We trying to update firmware via DFU.
Problem definition : First we update firmware via DFU application boot...
Hi ,
We have a custom hardware with an Active GPS Antenna (that is connected to the main board with u.fl connector).
I ran the GPS SNR command to test the performance...
I'm designing a PCB that uses the nrf52832 with an external RTC, the DS1339 ( https://datasheets.maximintegrated.com/en/ds/DS1339-DS1339U.pdf ). I want to use a single 3.3V...
I'm enabling external power off warnings, as specified in section 5.22 of the AT command guide.
When I drop the supply voltage I see a LTE network disconnected message from...
Hello Nordic!
I have been developing a Zigbee application and now, I need to connect via Serial communication with another device. I just need to listen to the port, not...
I am using flash_fstorage_s140_pca10056 example from SDK v17.0.2 , I see that the start address is 0x0003 E000 and the end address is 0x0003 EFFF respectively.
I want to...
Hi,
I am trying to check how DFU works but I have problems setting it up. I will describe all the steps that I have been doing here, so that it will be easier to try to...
Hi, I am designing a custom board usign the NRF52832. Im using this externar crystal https://es.rs-online.com/web/p/unidades-de-cristal/1753468/ . but I have seen that many...
Hello Nordic Support Team
I need desperate help to get my proof of concept working. I have been able to prove that the applicational concepts work on the nRF52840 and now...
I'm trying to create an application on the nRF52840 that can read serial input from an external GPS chip and also provide log output via USB. As I understand it, the UART...
I want to read access address of a connection between master and slave in master.
I need access address and not the MAC address after connection establishment.
Is there...
Hello, when developing our application, we run into a problem. We are running Zephyr 2.4.0 on nRF52840 MCU. We use LSM303AGR sensor, which is supported by zephyr LIS2DH driver...
Hi,All:
1. As the topic, now i just make bootloader,How do i perform a app entrance? and how to staging, combing.........in the picture as below. Or,on the other hand,how...
Dear,
I am trying to manually toggle GPIO0_2 by writing into the GPIO register, 0x50842504[bit 2]. The output of GPIO0_2 was always static in either high or low.
If...
