Hi We are working on setting up CI/CD pipelines for our nRF application. The application is set up as a stand-alone application with its own west workspace. It uses external...
Hi ,
1.In the example: In nRF5_SDK_17.1.0_ddde560_usbd_msc_1\components\libraries\block_dev\qspi\nrf_block_dev_qspi.c, I need to set the following 0xB7 bytes. How should...
Hi I'm testing the current consumption of the external qspi-flash on nrf5340dk [ MX25R6435F]. I have used ppk 2 to measure consumption with the dk and also have used a power...
During the development of a Matter over Thread product, I encountered the following issue:
After adding two Matter over Thread devices (an OnOff Switch and an OnOff Light...
Hi Nordic Teams :
I would like to check the current consumption by BLE DTM.
1. Is the table measurement is from 3.0V input?
2. I find the condition in the datasheet...
HI ALL,
nrf54l15dk,v2.8.0,peripheral_uart demo and no changes have been made.
Then add the following content to prj.conf
sysbuild.conf
mcuboot.conf
At this...
I'm developing my application with nrf 52832 and nrf SDK v17.
I know NCS is more powerful. I'm currently learning how to use it.
But now.I still need my application with...
Dear Nordic team,
we are facing a strange phenomenon - in idle mode (k_sleep(K_FOREVER)) we notice, that the current consumption drastically increases if a magnet is placed...
I have a production system running a modified asset_tracker_v2 sending temperature data to AWS. All is working fine with V2.5.0 on several hundred sensors. I am trying to...
Hi,
I am looking for procedure to make it work nRF240L01? I am getting documents for Arduino but as you know that is not understandable, with Arduino it worked but i don...
Using the Online Power Profiler for LTE we saw that nRF9160 would require 0.115 s to upload 4-kbit of data into the mobile network.
This is an U throughput of ~34-kbit/s...
Hi everyone,
I have found a Linux driver for the TLV320AIC320 external codec provided by TI:
TLV320AIC310X Driver: https://web.git.kernel.org/pub/scm/linux/kernel/git...
Hi,
I am currently encountering an issue with the error message 'sdu_ref_us not from consecutive frames' in the following scenario:
Broadcasting Source: A Samsung S23...
Hi Nordic Team,
in our project we want to write/read cryptographic keys to/from the KMU.
One of the algorithms we are going to use is ECDSA.
My naive approach was to...
For my project's purposes, I need to send data wirelessly and very regularly (every 3ms); it also needs to be power optimized. I got a version of my code to work using ESB...
Hello,
I am currently using the nRF54L DK and running the ESB (Enhanced ShockBurst) sample in nRF Connect SDK v2.8.0 . I would like to change the LF (low-frequency) clock...
Hi,
I need information about adding an additional flash IC to my project. However, I am wondering if there are any limitations regarding the maximum storage capacity that...
Hello, I am working on a project using a custom board with the nRF5340 chip and SDK 2.8.0.
In my setup, the application core reads sensor values, packages them into packets...
Working on a wearable health sensor using NRF5340. Hard to be certain of correlation, but glitches of varying magnitudes appear on my sensitive analog signals (as captured...
Hello Nordic friends,
I am currently testing the device, but I absolutely don't want to use Zephyr or any advertised MCUs. I wrote a simple code for scanning and testing...
I have a custom nRF52833 wired to an Adafruit USB Micro-B Breakout Board, and when I plug it into a Windows computer, it gives a device not recognized message and no COM port...
