I want to use the Softdevice Controller without a crystal on the RTC. I configured my project with
Advertiements look fine, but interaction with a BLE central either throw...
Hi everyone,
These days I'm evaluating the Nordic nRF5340 to manage audio from two microphones to one dongle station. To achieve this, I configured two nRF5340s as unicast...
I am planning to use 3.7V non Rechargable Battery with Diode and Reverse Protection circuit with npm2100, Would like to build a Fuel Guage model for this as this is not available...
Hello,
I am currently evaluating MCELL location on an existing project, based on nRF9160.
After some trial and errors, I managed to get it working.
However, I ma a bit...
HI
I am currently using the nRF54L15 chip with NCS 3.2.1, carrying out secondary development based on the periodic_sync_conn sample project. I intend to adjust the transmit...
Hi,
We are developing an application that requires synchronization between two or more nRF9160-based devices. We have the following requirements and constraints:
Required...
I'm using the prebuilt Aliro stack (libaliro.a, nRF52840), when a session fails inside the library we have no way to get the resulting AliroErrorCode. The stack entry points...
This is a strange problem. 10% of our production boards fail outdoors within tens of seconds and will not fail after tens of minutes if indoors . The rest of our production...
Hello,
is there some existing example for nRF52840 DK, that would allow setting my own custom HID descriptor? e.g. "Telephony page (0x0B)" or a custom vendor-specific HID...
Hello,
I'm building a project for a nRF5340 and i need to use the mesh_stack.h library to reset device mesh configuration however every time i try to include it i get...
tutorial followed: https://devzone.nordicsemi.com/nordic/short-range-guides/b/bluetooth-low-energy/posts/ble-characteristics-a-beginners-tutorial
I have followed the above...
Hi,
Now, I have a provisioner (based on the provisioner example of the mesh sdk) and I want to unprovision a specific device.
I have tried to use "config_client_node_reset...
Hi,
I have three nRF52840 DKs
I am trying to connect two of them as peripheral devices( that implement the ble_app_uart example)
to the third nRF52840 central device...
Hi guys new to the Nordic family of devices, but can the thingy91 provisioned on a third party cloud platform other than the nrfCloud? Also can I use a different sim-card...
While migrating to the latest nRF5 SDK (17.0.2) and nRF for Mesh SDK (5.0.0) , I've noticed that they ship with Softdevice 7.2.0 .
The latest s132 Softevice available for...
Hi,
I understand that scan request allows the broadcaster to send additional advertising data. Does it send the additional data via data channels? Is it related to secondary...
SEGGER ver 5.50d
nRF52840
I'm trying to find a way how to use the STL library with GCC compiler. I know that SEGGER is not fully supported STL library (a basic stl library...
Hi,
We are developing a solution using nRF52 and nPM1100 using nRF5 SDK 17.x? I was wondering if there is a software library already written for the nPM1100?
Thank you...
Is it possible to change the smartbasic firmware? and if I want to return to that firmware how can I doit?, and last one, if I use de nordic SDK with the DVK BL654, does it...
Optimization level is set to "Debug". Tried to change it to one of the Levels, however then firmware does not run at all. Debugging Level is set to Level 3.
Can it be other...
I want to develop the nRF series at segger embedded studio for the first time. But I tried the following homepage to install manually. www.nordicsemi.com/.../Segger-Embedded...
