We recently encountered an issue with incompatible image partitions being pushed to in-field devices causing soft bricking. refer to this ticket for more information
Problem...
Page 399 of nRF54L15/nRF54L10/nRF54L05 Datasheet v1.0 shows:
CLK = PCLK32M/(2*PRESCALER)
but this formula does not match the values in the examples in Table 46.
I CAN...
Hello Nordic Team,
I am currently working with the nRF52832 on a custom board using nRF Connect SDK v2.9.0. I am implementing OTA DFU using Sysbuild and MCUboot with an...
Hi Team,
I am working on OTA using an external Winbond flash IC (W25Q64) with the nRF52832 controller in NCS SDK version 2.9.2. I have completed all the required configurations...
Hi team,
We are going to kickoff a new project of 2-mic AI recording pen. Good to see we got a very high performance for 54LM20B with DSP/NPU, which might be a very good...
Hello,
We are currently developing a Zigbee product using nRF Connect SDK v2.8.0 . While reviewing the release notes for NCS v2.9.0 , we noticed two critical bug fixes related...
Hi Nordic team,
I have a question regarding the RF matching networks used in the nRF54LM20A-PAAA reference design and in the nRF7002 Expansion Board II (PCA63571).
For...
Would it be possible to be talked through the steps of setting up SPI with the nRF52833DK using the Zephyr RTOS? I am new to the Zephyr RTOS and have so far been unable to...
Dear BLE mesh experts,
This is how the provisioning screen of my Android app looks:
The intention is to enable the user to provision various unprovisioned ble mesh devices...
I am reading through the code and would like to understand the following macro
#define DRV_RTC_INSTANCE(id) \ { \ .p_reg = NRFX_CONCAT_2(NRF_RTC, id), \ .irq = NRFX_CONCAT_3...
Hello!
In the description of the usb module, I found the registers: NRF_USBD-> DPDMVALUE, NRF_USBD-> TASKS_DPDMDRIVE and NRF_USBD-> TASKS_DPDMNODRIVE
" State D+ and...
Hello,
I have been writing to my nRF9160 for the past few weeks now, no issues. My board was working fine yesterday. I left it on overnight to see how much battery it...
Info:
Windows 10
Segger Embedded Studio V5.20a
SDK16.0.0 & Mesh SDK 4.1.0
nRF52840 & nRF52832
I'm setting up a friend node and a low power node. The friend node...
Have used nRF Connect V3.30 for the past year to program nRF52DK with USB and nRF52832 BLE modules with Segger J-Link Base programmer without issue. Updated programmer app...
hi ,
I am working on the nrf525832 , i want to store the data which is sent from phone via BLE using nrf toolbox . I tried to merge the flashwrite and ble_app_uart example...
Hi,
I have some questions regarding BLE:
1) What is the max payload size? Where can I find it?
2) What is the throughput in bps? Where can I find it?
3) Where...
Dear Members,
I got the value for cadence, speed and HRM, then display it to LCD,
but after they are all (the input) in 0 value,
LCD is not displaying zero, but still...
Hi,
Recently I am using BLE for transmission on zephyr on nrf52840 When my peripheral establishes a connection with central, the subscription is also successful My peripheral...
The chip runs in the app stage and calls a function to make the chip jump to the bootloader stage (DFU mode).
The SDK we use is nrf5_ SDK_ 15.3.0_ 59ac345,
We made the...
Hello!
I have the NRF9160 DK set up to use UART2 and listen to AT commands from external MCU, NRF52840 DK configured to send using UART0.
The NRF9160 set up is done, pins...
I want to transfer 1000Bytes. if I transfer 1000bytes every second after some time connection broken,
and need to reboot the device and connect it again
how can I solve...
