Hello everyone,
I'm reaching out to this forum in a bit of a bind and hoping someone might be able to offer some guidance or assistance.
I'm trying to download the S340...
Hello LE-Audio team,
By any chance, do you have a working code base that supports a headset with 2 end points instead of just one as your sample nRF5340_Audio kit?
If...
Hi, I just tried to connect LSM6DSV IMU with nRF52840dk
The whole folder structure is shown below :
1. I set nrf52840dk_nrf52840.overlay file first.
2. I...
Hello,
We are designing a new Zigbee/Thread end-device sensor and I'm wondering what is the recommended part for it.
I have a demo running with nRF5340 (because the platform...
Hi Nordic team,
I'm using the nPM2100 PMIC in my design to power a microcontroller. The microcontroller sets the nPM2100 into Hibernate mode , and a vibration sensor connected...
Hello,
We are currently using the nrf52840 for development using Zephyr v3.7.99-ncs1 .
We want to use the UART in low power mode and therefore, we have used the zephyr...
My attempts to configure the Zephyr device tree to run littlefs on an external SD card have repeatedly resulted in what appears to be the creation of a small littlefs instance...
Hi,
After updating NCS folder to latest Master branch, SES4.52 is not able enter into debug mode.
Receiving error as: failed to set startup compilation break point:...
I have a bootloader, softdevice and firmware (all with sdk 15.0 and softdevice V. 6) on a nrf 52840 on an counter-pcb.
I have upgraded the firmware to sdk 16.1 and use the...
Hello together, I am just starting to work with the nRF9160 and have some problems with the configuration. I inserted the iBasis SIM card and tried to get a LTE connection...
Hi,
I am using a ble_app_blinky example (SDK16) to communicate with the BLE devices. NRF52840 is connected with the client devices and successfully sending the data to the...
Hello,
I would like to know if it is possible to not use softdevice because i need more flash for my code. I guess it is possible but when i don't enable softdevice in my...
Hello,
i'm trying to use SPI with nrf9160DK as master and RFM96 module as slave. At the moment, i'm developing elementary functions to write and read from my slave device...
Hello
I am working on Nordic nrf52832
I am using the "ble_app_blinky_c_pca10040_s132"
I want to use ble for scanning a beacon (eddystone TLM) and collect its data. ...
please help. I need functional description of what is need step by step for doing a zigbee hardware device switch and management over bluetooth on the thingy52, i have all...
Hi Team,
We are using the NRF52840 with s140 Soft device for our BLE application.
While we are facing some issues while doing debugging.
1. We are getting Hard Fault...
Are there any issues of pairing a nRF52833 using OOB pairing with a IOS device? Is there a good example code I could start with?
Thank you very much.
All the best
P...
The system requirements: 50 identical nRF53-based devices (each with a sensor and an actuator), positioned within a 3x3 meter square should be connected to a single computer...
Edit : The code posted below works on the 96x96 3V(LS013B4DN04) variant of the display, I still have no idea why it doesn't work on LS044Q7DH01, but I'm guessing it doesnt...
Hello!
I have some devices with a custom built PCB on my desk, all of which have my own custom firmware on it.
Sadly the devices don't have access to the debug pins...
Hi Team,
May I know the functionality of the below mentioned signals:
MIPI RFFE interface pins: VIO, SCLK, SDATA. MAGPIO interface pins: MAGPIO0, MAGPIO1, MAGPIO2. ...
Hi,
I got a question on nRF52832 platform. When it is brand new (so without loading any of our FW) and powered through 3V3, it draws up to 4.6mA when powered. But we also...
