Hello,
I am using SDK v2.9.1 for a Bl653 (NRF52833) and was trying to use the Nordic Academy Example for how to setup the SPI bus. The Nordic Academy example states we must...
I'm currently working on configuring the nPM1300 used in our custom board. In the product spec v1.2, it supports 2 USB compliant current limits, IBUS at 100mA and IBUS at...
Hi,
I am currently trying to enable the GPIO output interrupt functionality on my nPM1300ek with an STM32. However, I am unable to get it work correctly(I was only able...
Hi,
What is the lowest possible current consumption for nrf52840 dongle dev board with zigbee ?
I'm using this for development and i'm getting 20-30uA in idle. Is it possible...
Hello, I am working on incorporating flash logging into an application that has a GRTC-driven EGU interrupt (capture/compare event). Here is where I am setting up the EGU...
We are experiencing some ESB link failures on the receiver end of our system: nrf54L15. After minutes to hours of use the receiver will stop getting data (we know the transmitter...
Hello,
I am developing a board with the SIP nRF9151.
I'm designing the board with a shared antenna for both the GNSS and LTE signals (Ignion NN02-224).
For the antenna...
I am rebuilding my computer after experiencing a corrupt boot sector and am reinstalling all my apps. I am moving from Kiel 4 to Kiel 5. My project loads, but it says that...
Our manufacturing supplier provided me a log file from the nrf Connect for Desktop Application that shows repeatedly unexpected disconnects when nrf Connect opens a second...
Hi,
Do you have a sample ANT radar profile example with all the pages defined, similar to ant_hrm.h in SDK 15.3 components/ant/ant_profiles/ant_hrm/pages/?
Thanks,
Abid...
Hi Admin,
I just bought development board Thingy 52 from Digikey. I coudn't find design files that consist of hardware design in Nordic website. Could you advise for this...
Hello,
I am currently tweaking the Thingy:91 to run a stripped down version of my custom application. I have been able to flash the device with the Thingy:91's sample at_client...
hi,
we're using a Adafruit nrf52832 board for a building a ble keyboard . w're able to pair to two central devices and appear to them as a keyboard , but for example : we...
Hi, we are designing a product that needs LTE connectivity and BLE for local setup.
The nRF9160DK uses an nRF52840 with some links for COEX and comms.
Is there any reason...
Hello,
is there any kind of good practice available about how to generate UDP traffic with the nRF9160DK via NB-IoT for a simple test?
As far as I know the AT client...
Hi
I followed below tutorial with my nrf52840 using SDK 15.3.0
https://devzone.nordicsemi.com/nordic/short-range-guides/b/bluetooth-low-energy/posts/ble-advertising-a...
Here is the software: https://www.nordicsemi.com/Software-and-Tools/Development-Tools/nRF-Sniffer-for-Bluetooth-LE which notably doesn't support the nRF52 dongle
I also...
SDK15.3
nRF52840
S140 v6.1.1
Q1. I have an RTC compare event connected to a Timer count task over PPI. The Timer is configured in low power counter mode. My question...
Hi, I am strugling to get the power comsumption down to the number I have been reading on this forum. I followed the instruction of the dev kit manual . When measuring the...
Hi, I'm getting regular crashes with my app: SOFTDEVICE: ASSERTION FAILED. Using and NRF52832, SDK 15.3.0, SD 132 6.1.1, and Mesh SDK 3.1.0. With DEBUG defined, I don't really...
I'm trying to interface 2 SPH0645 mics to the nRF52840 DK.
Little did I know when I bought them (the mics) that you need to waste 2 timers + 2 pins + memory space to make...
Hi,
I am trying to measure a signal using the SAADC driver on SDK 13. I have used the example from the nrf52 playground for low power ADC
I have a few questions on best...
