Help Needed: BLE Not Working on nRF52810 (Tried Zephyr & nRF5 SDK)
Hi everyone, I really need help getting BLE working on my custom board with the nRF52810 . I've been trying...
Hello everyone,
I'm reaching out to this forum in a bit of a bind and hoping someone might be able to offer some guidance or assistance.
I'm trying to download the S340...
Hello LE-Audio team,
By any chance, do you have a working code base that supports a headset with 2 end points instead of just one as your sample nRF5340_Audio kit?
If...
Hi, I just tried to connect LSM6DSV IMU with nRF52840dk
The whole folder structure is shown below :
1. I set nrf52840dk_nrf52840.overlay file first.
2. I...
Hello,
We are designing a new Zigbee/Thread end-device sensor and I'm wondering what is the recommended part for it.
I have a demo running with nRF5340 (because the platform...
Hi Nordic team,
I'm using the nPM2100 PMIC in my design to power a microcontroller. The microcontroller sets the nPM2100 into Hibernate mode , and a vibration sensor connected...
Hello,
We are currently using the nrf52840 for development using Zephyr v3.7.99-ncs1 .
We want to use the UART in low power mode and therefore, we have used the zephyr...
Hi,
I would like to update the Device Information Service's (DIS) serial number characteristic to reflect the actual serial number assigned by our production equipment....
Hi, I am using the following setup: Wireshark 2.6.5 (updated yesterday) Sniffer 2.0.0-beta-3 (nrfsniffer200beta312oct20181c2a221.zip) nRF52840-DK (used by the sniffer) nRF52840...
I have a custom board that uses Nordic NRF52832 as MCU. For laying out crystals, BLE part and decoupling capacitors, I used reference layout from documentation.
32 MHz crystal...
Hi everyone,
My hw/sw configuration:
- nRF52840 - sdk 15.0.0 - softdevice: s140_nrf52_6.0.0
I would like to change the device name and update it in advertising packet...
Hi All,
I have been working on ipv6 over ble on zephyr RTOS to form mesh network.I have been successfully integrated "rpl_node"(which is in zephyr/samples/net/rpl_node)...
Hi guys,
I have very strange problem with the Android phone when connect with nrf51822.
After connection, I used update parameters to set the parameters on the phone side...
Hello,
I am attempting to program nRF52 DK modules to communicate using the UART over BLE central and peripheral roles as in the examples provided in SDK 15.2. The data...
hello, I have used NRF52810 TWIM for 24LC08 communication, and I got a problem.
when I want to read data from 24LC08, if the length is not lager than 255, every thing is...
Dear all,
Good morning,
We are using nrf52832 as our main mcu. Our current consumption in system-off mode in custom board is around 3.2 mA which is very high and we want...
HI devzone
We now use NRF52832 to implement TDMA protocol.
In our application, there is one primary node and six sub-nodes.The communication process is as follows:
After...
I want to add simple on off switch model via SDK 2.2.0.
I'm already add client model to project,when provisioner add client node,Provisioner RTT jump error opcode status...
Hello Everyone,
Maybe this is a very silly question.
I am trying to implement timer in nrf51822 with S130, SDK11.
Code snippet:
void TIMER1_IRQHandler(void)
...
Hi,
i Have two development kits where one acts as uart central and another acts as uart peripheral .
In that i have given the peripherals different names( DEVICE_NAME...
Hi, I would like to ask how can i get the current consumption that was stated in the datasheet which is 0.7uA and the value I get from the reading is about 8-9 uA.
Is...
Hi team,
I am using sdk 14.2 ,nrf52840 DK board.
I am getting the following error while running nrf5-mpu-ble-simple code in keil. <error> app: Error 0x000D (13) at line...
