Hi,
The attached code is based on a sample code from NCS v2.9.1 and creates a LittleFS flash disk on external SPI NOR onboard nrf54L15DK. There is a mismatch in the code...
Somehow a program I have running on a nrf52840-DK board will enable protection. This kind of screws up the small application I am testing because it seems to lock out the...
Hello Nordic team,
I would like to automatically patch the merged.hex file each time I build my project. I’ve attempted to use extra_post_build in CMakeLists.txt , but my...
I noticed that the product information of the nRF54L15 series kit supports 4Mbps, but I'm unsure how to verify it. Are there any relevant examples available? I have currently...
Dear Nordic Support Team,
I am experiencing difficulties flashing firmware to my nRF52832 development board using VSCode with west flash , followed by J-Link...
Hi Nordic team,
We're experiencing two issues related to partition handling in Zephyr/NCS and are looking for your guidance
Issue 1: settings_storage is erased after BLE...
spim2、ncs2.6.1
I used SPIM2 to send the string "Hello, SPIM!" and receive data of the same length.
However, on the logic analyzer, I can only see the transmitted signals...
Hi,
We had a power issue with our custom board related to DFU updates. After performing a DFU we were seeing 8mA idle current, and when we had programmed the firmware directly...
Hello,
can you provide a best practice guide on how to use memory protection unit in nRF52832.
I am interested to know if MPU can protect user defined memory regions...
Hi,
I want to know Tx power and duty cycle information of Beacon and NRF52 for the following cases:
In our case NRF52 will be our receiver and Beacon will be transmitter...
During the CE immunity test, the nRF51822 has to re-connect automatically without user interaction when the BLE connection is blocken by noise. Please tell me how to implement...
hi,all
my device use CR2450 button battery,advertise time 500ms
TX POWER:4dbm,the battery life is low if it still use this configuration
(May be big current lead...
Hi all,
I am using a nRF52832 with SD S132 V4.0.2 ion SDK13.
My application currently uses TWI, SPI and BLE and also 1 wire (which is based on delays). Everything works...
Hi!
I am working with PCA10040 (nRF52), s132 and SDK 12.2.0.
I am using the example experimental_ble_app_eddystone.
I have configured one slot as TLM, so it reports...
Hello,
We're using JLinkExe for production programming. Is there an equivalent of the nrfjprog --erasepage command for JLinkExe?
I'm looking for the equivalent of
nrfjprog...
Hello,
I feel like this question has an answer similar to this question, but I can't seem to get it working devzone.nordicsemi.com/.../
I am using the nrf51422 chip...
Hello,
I bought a SainSmart display which fits on the PCA10028 development board. This display is a 16x2 character display with a HD44780 display contoller (I guess).
...
Hi,
i am new in nrf51822.
i want to make a pin as a external interrupt pin, whenever it get high to low pulse it will call in ISR.
here i am unknown how to write an ISR...
hi,
i have downloaded code to nrf52 BLE module using nr52 DK with VTG,SWIO,SWCLK connections. but here i am unable to display the log for nrf52 ble module. is it possible...
Hello, I got the solution for my previous errors, but now I'm facing new error, that now when I compile my code it gives error like invalid command name "nRF52"
ac2...
Hi everybody,
Chip: nRF51422
Board: PCA10028
Firmware: S130_nRF51_2.0.1
The system hangs when doing burst write reg.
MPU9255 can work fine if all writes are ...
