Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi, i'm using two nrf52840 DK ev kit. One it's the central and one the peripheral
After the connection I need to save power at the peripheral board, because the cpnsumptio...
In mesh example project “dimming_server”，I have added functions: mesh serial, SAADC(use ppi) and compie pass.However,when debugging,an error is happened in the function"nrf_drv_timer_init...
NRF52840 support the long range bluetooth and BLE gateway SDK, look at here that RAK Wireless held a Beta and welcome the community to participate.This board with Cellular...
Good day!
Started to work with nRF mesh. And wanted to add ir_lib from this project to Generic OnOff example.
And Source navigator shows error: static_assert failed "unspecified...
I'm attempting to build the aes_gcm sample using NCS 2.4.2 for a custom board with an nRF9160. However, I can just build the project for the nrf9160dk_nrf9160_ns target since...
Dear person in charging,
I would like to know the nrf52833‘s RF power accuracy at the emission power of +8dBm, because it is described on the data sheet that the power accuracy...
Hello
I am new to the NRF Connect and NRF board development. I was trying to run a blinky code on the nrf 52840 dongle using the nrf52840dk. I was referencing the following...
I have a Matter over thread temperature sensor, and low energy consumption is very crucial for me. Therefore, I'm using the Nrf2.7.0 SDK ICD LIT KConfig options and I found...
Hi I am receiving the error "Linking C executable zephyr\zephyr_pre0.elf FAILED:" which I have found is linked to the mcp7940 device tree node through the error code " undefined...
Hi, all,
I am new to nRF Connect SDK and am currently facing some configuration issues with the MAX30101 driver in a Zephyr project. Here is the example program and source...
Mac with M1 silicon, installed latest Mac-specific nRF Connect for Desktop (5.02) and latest command line tools: 10.24.2 macOS
DLL error in GUI app:
Command line fails...
HI
when I try to uninstall/remove my connect sdk, tool chain manager says:
Failed to remove C:\nordicsemi\v2.6.0, operation not permitted. Please close any application...
Hi I have been working on an project using nrf5sdk_17_1_0 using Segger 5.42a but when I try to build the Blinky example it gives me build failed without any syntax error
We are developing a sleepy end device using the nRF52840, based on the light switch sample. We have set zb_set_ed_timeout to 16384 minutes, which is approximately 11 days...
Hello,
I am using the NRF52832 in my PCB design, and I have attached a screenshot of relevant part of the layout. My PCB manufacturer pointed out that some vias overlap...
Hello,
I have had this issue from the first time I installed VS Code and the nRF Connect Extension.
When I open my project, the connected devices pane is just missing...
Hi,
Since we started testing the new nRF9151 with the latest modem firmware (v2.0.1), we’ve noticed a change in GNSS behavior compared to the nRF9161/v1.3.6.
Recently...
