The link for downloading nRF6939 live cd v5.4 is broken.
https://www.nordicsemi.com/Software-and-Tools/Reference-Designs/nRFready-Smart-Remote-3-for-nRF52-Series/Downlo...
Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
Basically, I cannot do continuous TX with nrf_libuarte_async:
Here is simple reproduce:
It only output ===TICK=== and no +++TOCK+++
Here is what I've tried:
...
Hi,
On the nRF52810, is there any limitation on using P0.12 with I2C? I am using MS50SFA module on a custom PCB.
I've also noticed the same issue on a nrf52 DK while using...
i use ncs1.5.0 and nrf5340dk_nrf5340_cpuapp, i disabled uart0 ,enabled uart3, disabled hci_rpmsg out ,and connect uart3 rx pin p0.32 ,tx pin p0.33 to a 232-usb connecting...
hi
I use nrf52 sdk17. i want to change device name .
1. if device name is less 19, more 18 ,it is ok. for example
#define DEVICE_NAME "123456789123456789" . it is OK...
Hi,
I'm trying to catch my NRF packets with nRF Sniffer for Bluetooth and I can't find them (after starting advertising).
On the other hand - I'm able to connect to the...
Hello,
I am stuck on the step of getting the Thingy91 to start working.
I am following this tutorial: https://www.nordicsemi.com/Products/Development-hardware/Nordic-Thingy...
Hi,
i am working on nrf52dk. i have already implemented dfu with button. i want to implement buttonless dfu. as there is a example provided in ble_peripheral with name ...
I'm more of a programmer than an electronics person so I apologise in advance if I misuse terminology or if the answer to this would be obvious if I had more experience. ...
Hello.
I want to raise the SDK version, what should I do at that time? (Example: v16.0.0 → v17.0.2) Should I overwrite all the old SDK sources I'm using with the new SDK...
Hi, I'm using the PWR_MGMT SDK 17.0.2 demo code on my nRF52 DK.
Q1) After enabling parameters in the sdk_config.h, the nRF52 DK could enter the Power Off Mode if I press...
I am trying to conduct a device firmware update using nrfutil's dfu ble functionality. Here is the command:
However, running the above command results in the following...
Has anyone used SDCard interface with either 52840 or 5340 in anything other than SPI mode? I just noticed in the SDK 15.3 code we are using SDCard is in SPI mode. Seems max...
Hello,
I want to connect an external led to the nrf5340 pdk to perform the same function as the blinky example.
I connected this led to D0 (PIN P1.00), but I don't know...
