Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hello,
I am using nRF52832 and having a problem with the Low Power Mode. I am not sure if I am either not getting it to stay in low power mode when my UART is initialized...
What is the maximum server node count running light switch example? In documentation there are multiple facts: 1) " If you have more than thirty boards for the server, set...
When I use the nRF Toolbox to upgrade the nrf52832 device on the mobile phone (huawei mate9 Android8.0), I have the following questions: The first time I opened the update...
The device sending data will be accepted to the callback function nrf_gzll_device_tx_failed， But the host side receives the data and calls the function nrf_gzll_host_rx_data_ready...
Hi!
I'd like some help in understanding the initiation of provisioning. We would like to have something along the lines of:
Using a mobile app, a user receives a list...
Because I encountered the same problem, so I needed help. I ran the nordic official example E:\sdk\nRF5_SDK_14.2.0_17b948a\nRF5_SDK_14.2.0_17b948a\examples\ble_central\ble_app_multilink_central...
I have successfully used the guide for BLE DFU.
But now I have trouble using the DFU via serial port. Do you have a guide for serial DFU?
I have tried two things.
...
I have a weird question:
On the nRF DKs (51&52) there are pin headers to connect them to an Arduino.
When delivered, on these headers there are some sort of plastic clamps...
As I working on a new project I am writing the code to support the new SDK driver structure and not including any "legacy" code support.
This highlights the fact that the...
I have a custom board with nrf51422-QFAC, used with SD 130 and SDK 12.3.0. My firmware consist of ble_app_hids_keyboard example modified. Schematics are attached below.
...
Hi all,
I using 1 Provisioner provisioning for some Nodes (light switch server) . If I have 5 Nodes in mesh network
I want to remove Node 4 from network and then add it...
I am working on a BLE peripheral (nRF52832 & SDK 15) which uses the Peer Manager to handle encryption and bonding to a previously existing central device. Sometimes bonding...
I am using the Segger Embeded studio and wondering about the SWO output.
I know I can load code and set break points with just SWDIO and SWDCLK.
So with RTT do I really...
