Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi, i'm using two nrf52840 DK ev kit. One it's the central and one the peripheral
After the connection I need to save power at the peripheral board, because the cpnsumptio...
In mesh example project “dimming_server”,I have added functions: mesh serial, SAADC(use ppi) and compie pass.However,when debugging,an error is happened in the function"nrf_drv_timer_init...
NRF52840 support the long range bluetooth and BLE gateway SDK, look at here that RAK Wireless held a Beta and welcome the community to participate.This board with Cellular...
Good day!
Started to work with nRF mesh. And wanted to add ir_lib from this project to Generic OnOff example.
And Source navigator shows error: static_assert failed "unspecified...
Looking at the schematic diagram of the ISP-1507-AX Test Board….
www.insightsip.com/.../ISP1507_AX_TB_Schematic.pdf
… I can see that there is the possibility to connect...
Hi
I am using ble_app_uart code from ble_peripheral folder and nrf_connect app to receive/send data.
I have interfaced external sensor with UART pins and receiving data...
Hi I am using UART code from nRF5_SDK_16.0.0_98a08e2\examples\peripheral.
I have checked loop back with default UART pins,which are 5,6,7,8.
Now I want to interface some...
Hello,
I am using a nRF52DK (PCA10056). When I connect the board, the J-link drive opens up, but it does not detect on nRF Go Studio, nor is it flashing any code. I am using...
I'm using the USB CDC ACM example to write a message to a com port. I can receive messages fine except there is one problem. I am receiving the characters one character at...
Hi,
Is it possible to use two LPCOMPs simultaneously?
I would like to use analog channel 6 and 5 and if I register a RESULT Above on channel 6 it should start a software...
Good day to all
I would like to get a little more information about the function:
added in softdevice version 7.0.1.
Starting the radio in connection mode is shown...
Hi,
I'm experiencing some UART issues on nRF52832 where it seems like the peripheral is not correctly reset when doing a soft reset. After a soft reset I expect that the...
Hi,
I am using nrf25840 Dongle as NCP with Linux machine. I have used NCP example hex from " nRF5_SDK_for_Thread_and_Zigbee_2.0.0_29775ac\examples\thread\ncp\usb_bootloader...
How to achieve the lowest power consumption while "sleeping" but still being able to awake from an internal timer ?
For the timer I'm using the Ticker class from mbed.....
Hi,
I am a Embedded System Engineer working in a Medical device company in Ireland. I have a ublox Modem(Nina-B111), which has a nRF5xxx module embedded into it. The modem...
Dear Sir .
I have on my custom board 2 spi , spi1 and spi3.
&spi3 { status = "okay"; compatible = "nordic,nrf-spim"; sck-pin = <31>; mosi-pin = <9>; miso-pin = <30>;...
Hi,
Now I use Nrf52811 to develop a product. I use the 125k long range radio + 4dB mode.
I read through its specifications and found no corresponding...
Hi,
Now I use Nrf52811 to develop a product. I use the 125k long range radio + 4dB mode.
I read through its specifications and found no corresponding...
Hi.
I programmed the firmware in " https://github.com/NordicSemiconductor/pc-ble-driver " share folder to a nrf52840 dongle.
NRF_SD_BLE_API=6
I took the example heart...