Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi, i'm using two nrf52840 DK ev kit. One it's the central and one the peripheral
After the connection I need to save power at the peripheral board, because the cpnsumptio...
In mesh example project “dimming_server”，I have added functions: mesh serial, SAADC(use ppi) and compie pass.However,when debugging,an error is happened in the function"nrf_drv_timer_init...
NRF52840 support the long range bluetooth and BLE gateway SDK, look at here that RAK Wireless held a Beta and welcome the community to participate.This board with Cellular...
Using the ble_app_uart example, Using oscilloscope to measure the time interval of broadcasting, two development boards are used respectively. One development board is nrf51422...
Hello, rols and hkn:
I got two different answer about watchdog and hardfault in devzone.
1. watchdog can't reset hardfault. https://devzone.nordicsemi.com/f/nordic-q-a...
https://github.com/bjornspockeli/custom_ble_service_example
I am currently following this example with SES on my NRF52840 DK (PCA10056). I copied the ble_app_template example...
Are there any recommended alternatives (& nordic plugins) to the discontinued Bluetooth Developer Studio? I'm looking for a tool to make the process of creating custom GATT...
Hi! I want to copy data from internal flash to a statically allocated buffer in RAM. I get a DACCVIOL hard fault try to do this by memcpy. The hard fault depends on the number...
I need to send 5 sensor values received over SPI to an app over BLE about 5 times a second. I also need to send a few configuration parameters from the app back to the nrf52...
I am using nRF 52 DK connected to Arietta with ARM Linux (4.2.6) 32 bit.
when I was trying to install "vcpkg" using "./bootstrap-vcpkg.sh", I am getting some errors as shown...
I have a phone app which talks to my peripheral device running the nrf52832 and so I will eventually add another peripheral device which ideally can communicate directly to...
Hello everyone!
I'm working on a project where there are 2 microcontrollers: the Nordic nrf52832 and a 3rd-party uC (can't disclose it). A protocol to transfer the firmware...
I feel confused about bearer. what's the difference between mesh-bases bearer and PB-ADV bearer or PB-GATT? there is little knowledge about mesh-bases bearer within mesh profile...
Good afternoon,
At the place I'm working there's 2 main projects using the nordic SDK, while one runs on the 12.3 version, the other is very outdated and still runs on...
Hi,
I'm having a problem at the moment with code based on Espruino on nrf52.
I connect as follows:
ble_gap_scan_params_t m_scan_param;
memset(&m_scan_param, 0,...
I've seen a few post that have similar issues but none that solve my problem.
I have two uarts (uarte0 and uarte1).
I disable them before going to sleep.
I wake with...
Hello,
I cannot successfully flash an nRF9160-Dk to a usable AT modem state using a brand new install of nRFConnect on Windows10, following this Blog post guidance - https...
