I have a simple TCP client application running on the nRF9160. After connection to the server, recv is called and writes the data over Segger RTT channel 1, where on the host...
Hi,
firstly, I have to say, I use MBED OS, if you cannot help me because of this, I understand, but maybe somebody still has some general Ideas.
I am trying to build an...
Hi everyone,
Currently, I am working on my bachelor thesis for creating simple network by using MQTT, BLE-6LoWPAN and nRF52832. I have three nodes of 52832 and one raspberry...
Hello everyone!
I want to form an Openthread network with three Nordic nRF52840 cardboards. I would like to monitor the traffic using a sniffer, but i can't receive any...
We are using the development board PCA10040 for implementing a prototype with several GPIO interruptions.
We are trying to use the NFC pins (pin 9 and 10) as pins of GPIO...
Development Software:
nRF5 SDK for Mesh v3.1.0
SEGGER Embedded Studio for ARM v3.50
SoftDevice S140 v6.1.0
Computer Platform:
Windows 10 Professional
Hardware...
Hello Nordic,
We developed our product using MCU NRF52840-QFAA-F-R. Our client is based in the EU. We plan to launch our product in 1-2 months.
I have a few questions...
Hello,
I am working on a prototype Bluetooth Low Energy module using the MDBT50Q-512K (by Raytac).
To measure the frequency of this prototype with test equipment, I am...
has been helping me connect to a device and I am finally able to do that, but as soon as I do, Zephyr crashes.
This is with a lightly modified central_uart project [00:00...
While creating a new board in step 2 of the exercise, there are a couple of problems with the sub-steps 1-5:
First, sub-step 1 says to name the board "DevAcademy nRF52833...
Hello,
I've been using the libuarte module in my project, and I done a power consumption reading. With libuarte switched on I'm consuming 0.78ma, and with it switched off...
We have been seeing a bootloop issue on some of our nRF52840 boards running NCS v2.6.1 using CR2032 coin cell batteries. The batteries are all around 3V.
This is an intermittent...
ON NCS SDK 2.7.0 version, how to calibrate SAADC?
I checked below code, I see that "Perform calibration before the reading is taken if requested.", it will trigger calibration...
I am developing a product for a customer using NRF9151(ncs2.7.0, modem fw: mfw_nrf91x1_2.0.2). While verifying it on the DK board, I discovered an issue. When the system starts...
Hi!
I'm writing new firmware for the nrf54 family, and I want to have a system timer with 1s resolution (clock). This clock will be occasionally synchronized with epoch...
I am currently working through the Nordic Academy - SDK Intermediate Course - Lesson 2 Exercise 3, found here:
academy.nordicsemi.com/.../
I am not seeing any of the...
Hi,
Going through the nRF Connect SDK Intermediate course on Lesson 2 exercise 2 step 9 there is a command ncs_install_path/PathToToolChain/opt/zephyr-sdk/aarch64-zephyr...
Hi,
I've recently brought up the Matter Test Harness on a Raspberry Pi following the instructions in the CERT tool repository ( https://github.com/project-chip/certification...
I know the default answer is no, stopping nrf24 and get a RF52 or nRF53 series but my question is about an existing product. We are not all FORD, we can not just do a mass...
Dear Nordic Support Team,
I'm currently working with your Flutter library, mcumgr_flutter version 0.4.1, to implement Device Firmware Update (DFU) functionality. However...
At first you only did that for nrf apps, which was already annoying, but I could live with it: https://github.com/nrfconnect/sdk-zephyr/commit/3239cf77c0ed7c58aefb1f368c8ad17303b16ef5...
